514296
24
Verklein
Vergroot
Pagina terug
1/113
Pagina verder
eZ430-Chronos Sports Watch Software
www.ti.com
3.2.1.3 Temperature Mode
Press "*" until the temperature mode is active (see Figure 3-1 for details). The temperature can be shown
in degree Celsius or Fahrenheit. The selection depends on the time mode setting. In 12H mode, the
temperature is shown in degrees Fahrenheit, in 24H mode in degrees Celsius. The temperature is
measured in 1-second intervals. Positive temperatures are marked with a small arrow pointing up in the
upper LCD line, left of the temperature. An arrow pointing down indicated temperatures below zero.
Secondary function: None
Set function: Temperature calibration (can also calibrated from PC software in Sync mode, see
Section 3.3).
1. Hold "*" for three seconds until the temperature starts to flash
2. Set the temperatures by pushing the "UP" or "DOWN" button
3. Press "*" to confirm the settings
NOTE: The temperature is measured inside the watch right inside the CC430 device. When the
watch is worn, the temperature of the watch may be different due to the body heat. For
accurate temperature measurements, do not wear the watch and allow a sufficient amount of
time for the watch to adapt to the surrounding temperature.
3.2.1.4 Altimeter Mode
Press "*" until the altimeter alarm mode is active (see Figure 3-1 for details). The altitude can be shown in
metric or imperial units. In 12H time mode, the altitude is shown in imperial, in 24H time mode in metric
units. The altitude is measured only when the altimeter mode is active, and measurement happen in
intervals of 1 second.
The implementation of the altitude algorithm is done according to the VTI's application report AN33 without
any additional low-power optimizations. Therefore, the altimeter is active only in altimeter mode. In
addition, a timeout deactivates the measurements after 60 minutes. Altitudes above sea level are
indicated with a small arrow pointing up in the upper LCD line, left of the altitude. Altitudes below sea level
are indicated with a small arrow pointing down.
The altimeter algorithm is based on the air pressure and the ambient temperature. Therefore, changes in
air pressure affect the altitude accuracy. For precise measurements, the altimeter needs to be calibrated
manually upon weather changes.
NOTE: For most accurate altitude measurement, the watch needs to be fully exposed to the
ambient temperature (that is, the watch should not be worn directly on the arm), because
temperature is part of the altitude measurement (see Section 3.2.1.3).
Secondary function: Re-activate altimeter after timeout
Set function: Altitude calibration
1. Hold "*" for three seconds until the altitude starts to flash
2. Set the altitude by pushing the "UP" or "DOWN" button
3. Press "*" to confirm the settings.
24
eZ430-Chronos Software SLAU292DNovember 2009Revised March 2011
Submit Documentation Feedback
© 2009–2011, Texas Instruments Incorporated
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Texas Instruments eZ430-Chronos bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Texas Instruments eZ430-Chronos in de taal/talen: Engels als bijlage per email.

De handleiding is 7,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info