6 7 8 9 10 11
CARE AND CLEANING
The appliance must be switched o and disconnected
from the charger before cleaning.
Remove any attachment tted.1.
Clean the blades and comb attachments with the 2.
cleaning brush (supplied) to remove remaining
loose hair clippings.
Clean the housing of the groomer with a soft, dry 3.
cloth.
The cutting blades of the clipper attachment 4.
should be lightly oiled with the oil provided once
every few haircuts.
STORAGE
Always let the appliance cool fully before storing.
After cleaning, store the appliance, charger and all the
attachments in the storage pouch provided.
SPECIFICATIONS
Model: .................................................................GR16
Net weight: ........................................................350 g
Noise gure: .......................................................70 dB
Groomer
Power supply: . 3V (NiMH rechargeable batteries)
Charger
Mains supply voltage: . 100-240 V~, 50/60 Hz, 0.2 A
Output rating .............................................3 V , 1 A
Class II double insulated. This product must
not be connected to earth.
WARRANTY
Your appliance is covered by a warranty for 12 months
from the date of purchase. If a fault develops during this
period, please return the unit to your nearest Tesco store
together with the original receipt as proof of purchase.
This warranty in no way aects your consumer rights.
UK: Waste electrical products /batteries should
not be disposed of with household waste.
Separate disposal facilities exist, for your
nearest facilities. See www.recycle-more.co.uk
or in-store for details.
ROI: Produced after 13th August 2005. Waste
electrical products/batteries should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
Switch on the groomer.3.
Gently move the groomer across the skin as shown, 4.
against the direction of hair growth.
The hair will be trimmed to length.
Sideburn trimmer - trimming edges etc:
The Sideburn trimmer attachment can be used without
the comb tted to trim sideburn edges etc.
Follow the instructions in the previous section, but
without tting the comb.
The groomer will now remove all hair in its path.
Tesco Stores Ltd,
Welwyn Garden City AL7 1GA, U.K.
OPERATING INSTRUCTIONS
GR16 V0.2
WARNING: NEVER USE THE APPLIANCE
ON WET HAIR. IT IS ONLY DESIGNED
FOR USE ON DRY HAIR.
When using this appliance for the rst time it is
advisable to experiment initially on an area of light
hair growth.
Changing attachments:
There are 5 dierent grooming attachments. A dierent
grooming attachment is tted to the groomer for each
type of grooming.
To change attachments:
Sideburn trimmer - trim to length:
The Sideburn trimmer attachment is used with the
adjustable comb tted to trim sideburns to an even
length.
Fit the Sideburn trimmer attachment.1.
Slide the comb into the groove on the Sideburn 2.
trimmer.
The comb has three click-stops in the groove, so can
be adjusted for dierent cutting lengths.
Push the comb fully onto the trimmer to cut to 2mm
cutting length. Move out by one click for 3mm.
Move out by two clicks for 4mm.
Hold the body of the 1.
groomer and twist
the attachment in
the direction shown
until the lock marks
line up as shown.
Lift the attachment 2.
o the body of the
groomer.
Place the new 3.
attachment on the
head of the groomer
body.
Twist the attachment 4.
until the lock marks
line up as shown.
The attachment is
now ready for use.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
Trimming nose/ear hair:
The nose/ear hair trimmer is used to trim hair from the
nostrils and ears.
Fit the nose/ear trimmer attachment.1.
Switch on the groomer. 2.
Place the tip of the Nose/Ear trimmer head 3.
assembly against the protruding hairs of the
nostrils or ears to cut and remove.
Warning: only use the trimmer to remove hair from
the areas listed. Do not insert the trimmer more than
0.5cm into the ear or nostril. Risk of injury.
Switch o after use.
Precision trimmer:
The Precision trimmer has a small trimming head and
can be used for detail trimming.
Fit the Precision trimmer attachment.1.
Switch on the groomer.2.
Carefully use the Precision trimmer to detail edges 3.
etc.
Pressing the Comb against the head, start by 7.
clipping the sides from the bottom of the head
upwards. Slowly move the Clippers up towards the
top of the head cutting small amounts at a time.
Repeat step 7 around both sides and the back of 8.
the head.
Clip the top of the head from front to back.9.
NOTE:- Do not push the clippers or force the clippers
through the hair.
Corded use:
The groomer may be powered by the charger if the
batteries are fully discharged.
Connect the charger cable directly to the charging
socket on the base of the groomer.
Plug the charger into mains power.
Switching on:
Press the switch lock. While holding the switch
lock, slide the switch up (towards the top of the
appliance) to switch on.
Switching o:
Slide the switch down to switch o the appliance.
Body groomer:
The body groomer can be tted with combs to trim hair
to 1.5mm, 2.5mm or 3.5mm lengths. Alternatively,
the groomer can be used without a comb to trim away
all hair and shave the body smooth.
Fit the body groomer attachment.1.
To trim to a set length, clip one of the three 2.
groomer combs to the groomer head.
The combs are marked with their cutting length.
Switch on the groomer.3.
Draw the groomer head across the skin, against 4.
the direction of hair growth.
NOTE: To shave where there is longer hair growth, use
the clipper or trimmer to trim the hair initially, then
use the body groomer to nish.
Cutting hair:
Fit the clipper attachment.1.
The cutting length is set by tting one of the two
supplied combs. Each comb is reversible so the two
combs oer four cutting lengths - 3mm, 6mm, 9mm
and 12mm. Refer to the table below to convert salon
grade numbers to mm cut length.
Salon grade guide (#) Cut length (mm)
#1 3 mm
#2 6 mm
#3 9 - 9.5 mm
#4 12 - 13 mm
Choose a comb to give the cutting length you 2.
want.
The combs are marked inside with their cutting
length - 3mm, 6mm or 9mm or 12mm.
Clip the comb onto the head of the clipper.3.
Check that the clips at the side of the comb are 4.
fully engaged on the head of the groomer.
Before starting, comb the hair in the direction of 5.
hair growth as shown.
Switch on the groomer.6.
Thinning hair:
The Thinning attachment can be tted to the clipper
to thin out thick hair after cutting, particularly at the
front of the head.
Switch o the groomer.1.
Fit the Clipper attachment without a comb.2.
Clip the Thinning attachment onto the clipper 3.
head.
Carefully use the clipper to thin out the front fringe 4.
area by combing the clipper head forward lightly
through the hair.
Take your time to avoid removing too much hair.
To contour the neckline and area around the
ears:
WARNING: The blades of the clipper attachment are
very sharp when unguarded.
CAUTION: Care should be taken when using the clipper
attachment without a comb tted as it will remove any
hair that comes into contact with the blades.
Switch o the groomer.1.
Remove the comb attachment.2.
Switch on the groomer.3.
Position the clipper attachment so that only one 4.
edge contacts the hair.
Slowly shape the hair around the ears and contour 5.
the neckline by positioning the blades against the
neck and moving downwards.
For nal trimming of the hair, fringe or beard, use 6.
scissors.
After use
When you have nished, switch o the groomer by
sliding the On/O switch to the ‘OFF’ position.
Always clean the blades after use.
DIGITAL COPY
A digital copy of this handbook is available on-line at
www.tescotechsupport.com.
DISPOSAL
Before disposing of this appliance, the internal
rechargeable battery must be removed for separate
disposal.
NOTE: This process is not reversible.
Disconnect the appliance from the charger.
Switch on the appliance and allow it to operate
until it stops (battery power is exhausted).
Switch o the appliance.
Remove the blade assembly by twisting it anti-
clockwise.
Use a at screw driver to remove the plastic
switching bar as shown below.
Remove the small black and white plastic parts as
shown below.
CAUTION: Once the battery has been removed,
take precautions to avoid any contact between the
terminals.
Dispose of the appliance and the battery separately in
accordance with your local recycling regulations.
Remove 2 screws from the bottom cover, then
remove the cover.
Pull out the mechanism from the top of the outer
casing.
Take out the circuit board and battery.
Use a cutter to cut o the battery from the circuit
board.
Be careful not to short circuit the battery.
