514909
12
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
12 ARGON
ENGLISH
Übersicht
0505/2/ST-000690645.EMS 1B
ENGLISH
Adjusting Wheel Alignment (Fig.6.13 - 6.15)
Important: Your chair will only roll properly if the
rear wheel positions have been opti mized, which
means correct ly adjusting the wheel alignment.
To do this, measure [the distance between] both
wheels front and rear to ensure that they are
parallel to one another. The difference between
both measurements should not exceed 5 mm. To
adjust the wheels to make them paral lel, loosen
the screws and turn the axle sleeve accordingly.
When finished, make sure that all screws have
been properly tightened (see the page on torque).
Wheel Alignment
Seat height
Adjusting front seat height (Adjustable
frame, Fig.6.11)
1. Slacken the screw (1) and remove
the cover (2). This releases the height
adjustment fixing.
2. By turning the castor connection you
can continuously adjust the seat height
by +/- 1.5 cm. Using the marking (3) on
the castor connection, you can ensure
that both castors are set the same.
3. Ensure that both castors are set at the same
height, otherwise the chair cannot move in a
straight line.
4. Ensure that the bolts (4) always face outwards
and are at right-angles to the direction of travel,
so that it will move in a straight line.
5. Replacing the cover (2) and tightening the
screw (1) secures the height adjustment fixing.
When doing this, be careful to observe the
starting torque.
Adjusting the directional stability (Fig.6.12)
1. Slacken the screw (1) and remove the cover
(2). This releases the height adjustment fixing.
2. Bring the castor fork at right-angles to the
direction of travel and put a set-square onto
the straight surface (3) of the fork.
3. By turning the castor connection, the castor
can be turned inwards or outwards to correct
directional stability.
4. Replacing the cover (2) and tightening the
screw (1) secures the height adjustment fixing.
When doing this, be careful to observe the
starting torque.
Argon tracking adjustment
3. Setting the toe-in/toe-out to zero
NOTE: On a wheelchair with 0°
camber cylinders it is not possible
to set toe-in or toe-out. This setting
is necessary only with 3°, 6° and 9°
camber cylinders.
The term “toe-in or toe-out” defines
how well the rear wheels of the
chair are aligned in relation to
the ground. This determines how
well the chair will run. Normal
resistance or rolling resistance
is provided, when toe-in is set to
zero.
To set toe-in/toe-out to zero:
Slacken the 2 screws (1) (1 each
side) which secure the angle
tube clamp. Check the ball in the
horizontal (2) plane and turn the
angle tube (3) until the ball is in the
centre. Toe-in is now zero.
Before tightening screws (1), check
that the camber tube is centred
left-to-right. The gap should be
the same on both sides, or there
should be no gap at all. Tighten the
screws to 7 Nm.
Width adjustment of the
wheelbase
K. REAR WHEELBASE
The rear wheelbase is defined as
the distance between the upper
side of the rear wheels and the
backrest tubes, and is represented
by measurement X. The factory
setting is (1.25 cm). A bigger gap is
usually required when a sufficient
gap between the tyres and optionally height-adjustable armrests
has to be created.
NOTE: When adjusting the rear wheelbase, adjust first one
wheel then the other. If both sides are slackened at the same
time, the adjustment of toe-in/toe-out will be altered.
To adjust the rear wheelbase, the parts of the camber (4) move
telescopically into or out of the camber tube (5), and lock into
place when they reach the end. Slacken screw (6) (located
closest to the camber tube) on the left side of the chair. Move
the quick-release axle inwards or outwards to achieve the
desired wheel base. Tighten the screws to 7 Nm. Repeat this
procedure on the right side of the chair and adjust the gap so
that it is the same amount as on the left side.
3
2
Fig.6.15
Fig.6.14
1
Fig.6.13
1
2
33
Fig.6.12
1
2
3
Fig.6.11
4
5
6
Fig.6.16
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sunrise Medical Argon bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sunrise Medical Argon in de taal/talen: Nederlands, Engels, Frans als bijlage per email.

De handleiding is 1,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info