514909
11
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
ARGON 11
ENGLISH
0505/2/ST-000690645.EMS 1B
ENGLISH
Footplate Adjustment
Divided and Platform
Footplates
(Fig. 6.4 - 6.6)
Footplates can be flipped up to
facilitate getting in and getting
out of your wheelchair.
They can also be tilted to six
different angles relative to a
level surface. Tighten screw (1)
firmly on the outer side.
By removing the clips (2), the
footplate can be adjusted to
three different positions toward
both the front and rear.
Loosen the adjustment screw
(3) to change the horizontal
position of the footplate. For
this purpose, the footplate must
be flipped up. When finished,
make sure that all screws have
been properly tightened (see
the page on torque). A minimum
interval of 2.5 centimeters from
the ground should always be
maintained.
Adjusting the Footrest (Fig.6.7)
Removing screw (1) will allow
you to adjust the footrest to
correspond to the length of
your lower leg. The angle of
the footrest may be indi vi d ual ly
adjusted (not rigid foot rest) by
loosening nuts (2). The footrest
bracket (3) prevents feet from
un inten tion ally slipping out place.
When finished, make sure that
all screws have been properly
tightened (see the page on
torque).
Castors, Castor Plates, Forks
From time to time the wheelchair may veer slightly to the right
or left, or the castors may flutter. This may be caused by the fol-
low ing:
Forward and/or reverse wheel motion has not been set •
properly.
The castor angle has not been adjusted properly.•
Castor and/or rear wheel air pressure is incorrect; wheels •
do not turn smoothly.
The wheelchair will not move in a straight line if the castors
have not been properly ad justed. Castors should always be
adjusted by an authorized dealer. The castor plates must be
readjusted, and the wheel locks must be checked any time the
rear wheel posi tion has been altered.
Castor
Seat
Castor
Adjusting the castor (Fig.6.9 - 6.10)
To ensure that both forks are set parallel,
simply count the teeth visible on both sides.
After setting the castor fork, the teeth will
guarantee a secure position, allowing an
adjustment of 16° in 2° increments.
Use the flat side to check for a right-angled
position to the ground.
The patented design allows the castor fork
to be turned, so that it can be reset at right-
angles to the ground when the seat angle is
changed.
Adjusting the seat height
(Fig.6.8)
To adjust rear seat height, slacken
and remove the 4 Torx screws
(1) (2 each side) and the thread
washer (2), which secures the
clamp (3) for the camber tubes
to the axle plates (4). Adjust the
two camber tube clamps (3) to the
required height and replace the 4
Torx screws. Before tightening the
screws, please follow the instructions for setting the toe-in/toe-
out to zero (See Fig.6.13 - 6.15).
Tighten the screws to 7 Nm.
NOTE – An adjustment to the castor angle may be necessary
when adjusting the rear seat height.
1
Fig.6.4
2
Fig.6.5
3
Fig.6.6
22
1
Fig.6.7
1
2
3
Fig.6.8
Fig.6.9
-8°+8°
Fig.6.10
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sunrise Medical Argon bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sunrise Medical Argon in de taal/talen: Nederlands, Engels, Frans als bijlage per email.

De handleiding is 1,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info