Handleiding Stomer SMS-1800-T (pagina 10 van 28) (Engels)

555292

Verklein

Vergroot

Pagina terug

1/28

Pagina verder

● When sawing oak-, beech- or ashwood.

● The dust collector must conform to the following

requirements:

● The diameter of the dust exhaust pipe must ﬁ t properly

(34 mm);

● The air ﬂ ow volume must exceed 550 m³/h;

● The vacuum at the dust exhaust exit must be ≥ 740 Pa;

● The air speed at the dust exhaust exit must be ≥ 20 m/s;

● Follow the user instructions for the dust collector.

CONNECTION TO AC POWER

High-voltage!

● Only operate this machine in dry surroundings.

● This machine may only be connected to a power source

that fulﬁ ls the following requirements (also see the

section "Technical data"):

– The mains voltage and the system frequency must

conform to the voltage and frequency that is indicated on

the technical data sheet of the machine;

– Fusing protection with a residual current device (RCD),

with a sensitivity of 30 mA.

– Sockets must be properly installed, earthed and tested.

– Position a power cable in such a way that it does not

hinder the work and cannot be damaged.

● Protect the power cable against heat, aggressive ﬂ uids

and sharp edges.

● Only use rubber-coated extension cables with a sufﬁ cient

wire cross-section (3 x 1.5 mm²).

● Do not use the power cable for pulling the plug out of the

socket.

OPERATIONS

This saw can be used as a:

● Cross-cut saw

● Table saw

Before making any changes in the settings of this

machine, always remove the plug from the

socket.

CROSS-CUT SAWING MODE

SAFETY INSTRUCTIONS FOR THE MOVABLE

SAW BLADE GUARD (FIG 2)

The movable saw blade guard protects against accidental

contact with the saw blade and ﬂ ying wood splinters.

The movable saw blade guard must always return

automatically to the start position, whenever the saw head

is lifted. The saw blade must be covered at all sides, when

the saw head is located in the start position.

SAFETY LOCK (FIG 3)

The safety lock blocks the saw head in the topmost position,

and it prevents that the movable saw blade guard exposes

the saw blade.

The safety lock is released by pushing on it. The saw head

can now be lowered; as the saw head is lowered, the saw

blade guard retracts and the saw blade is freed.

After a cut has been made, and when the saw head is back

in the topmost starting position, the movable saw blade

guard is once more blocked by the safety lock.

TRANSPORT

● Position the lowest saw blade guard over the saw guide

piece and push backwards until you hear a click, and until

he saw blade protector is positioned at the black line on

the saw guide piece.

● Lower the saw head by pushing in the safety lock and

activate the locking pin.

● Lift the machine up by grasping both sides of the base.

Note: The essential operating components of the

machine are presented in this section. Make sure

to read this section, before you use the machine

for the ﬁ rst time.

TABLE SAW OPERATING MODE

● Make sure that the table is mounted completely and in

the right direction – and that the locking pin is properly

locked.

● Release the table stops, so that you can push down the

table. Then lock with stops. (8&9)

● The ON/OFF switch is used for starting and stopping the

machine. (1&2)

CROSS-CUT AND MITRE SAW OPERATING

MODE

● Release the table stops so that the table can be pushed

up by springs. After that lock with

the stop.

● Remove the lower saw blade guard. (41)

● For starting the motor, push on the switch in the handgrip.

(13)

● To switch off the motor, release the switch.

TURNTABLE (16)

The turntable can be turned 49° to the left and 49° to the

right, and it can be ﬁ xed in preset positions of 0°, 15°, 22.5°,

30°, 45°.

For turning the mitre table, the locking knob must be

released.

To prevent that the mitre angle changes while sawing, the

locking knob of the mitre saw must be tightened (also when

the saw has been ﬁ xed at a preset stop).

ADJUSTMENT OF THE BEVELLING ANGLE

The support arm can be tilted vertically and in an angle of

45° to the left.

To be able to tilt the support arm, the bevel lock must be

released.

To prevent the bevel angle from changing while sawing, the

locking knob of the support arm must be tightened.

MITRE AND WIDTH GUIDE

The mitre and width guide is mounted on the top saw table.

The mitre and width guide locking knob must point towards

the front of the machine. Once the locking knob is released,

the mitre and width guide can be removed.

CONNECTION TO A DUST COLLECTOR

The dust of some types of wood (such as for instance

beech, oak and ash) can be hazardous if inhaled. Always

use a dust collector:

● If the saw is set up in an enclosed space;

● Whenever the saw is being used for longer periods of

time (more than a half hour per day);

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Stomer SMS-1800-T Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info