555292
8
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
8
This laser complies with class 2 according to the relevant
standard. The unit includes no servicing components.
Do not open the housing for any reason. If the unit is
damaged, have the damage repaired by an authorized
repair agent.
Laser viewing glasses are not protective glasses against
laser radiation.
ADDITIONAL SAFETY INSTRUCTIONS FOR
CROSS-CUT AND TABLE SAWS
Always wear eye protectors.
Never use the equipment in the presence of ammable
liquids or gases.
NEVER use the equipment when a cutting disc (and not
a saw disc) has been attached.
Before each use, check the saw blade for small cracks
or damages. Replace a cracked or damaged blade
immediately.
Never use saw blades made of high-speed steel (HSS).
Only use saw blades that are recommended by the
manufacturer and that ful l the EN847-1 standard. Also
make sure the riving knife is not thicker than the width of
the saw cut, and that it is not thinner than the body of the
saw blade.
Always use the accessories that are recommended by
this manual.
Select the correct saw blade for the material must be
sawn.
To reduce the generation of noise, always make sure that
the blade is sharp and clean.
Only use correctly sharpened saw blades. Never exceed
the maximum speed that is indicated on the saw blade.
Before installing the saw blade, clean the axle, the anges
(especially the assembly surfaces) and the hexagonal
nut. Incorrect mounting can lead to vibrations/knocking
or slipping of the saw blade.
Wherever possible, use the saw guard and the riving
knife with every type of application, also when sawing
material in two. Always mount the saw guard according
to the instructions in this manual. Cutting operations
are those where the saw blade cuts completely through
the workpiece, such as for instance when doing
longitudinal cuts or shortening workpieces. NEVER use
the equipment with a defective saw guard, and never tie
up the saw guard with a rope or cord. Every irregularity
in the operation of the saw guard must be immediately
corrected.
Immediately replace the saw guard and the riving knife,
after a process has been completed that required their
removal.
Prevent that the saw comes into contact with metals, such
as nails and screws. Search for and remove all nails,
screws and other foreign materials from the workpiece,
before you start to work.
Remove spanners, cut off pieces and the other items
from the saw table, before turning on the switch.
NEVER wear gloves while working; the wearing of
gloves is only recommended while cutting tools are being
replaced.
Make sure that your hands stay clear of the cutting line of
the saw blade.
NEVER stand in the cutting line of the saw blade and
NEVER let anyone else stand in that position.
Remove any adjusting keys or spanners before turning
on the power tool. A spanner or key left attached to a
rotating part of the power tool may result in personal
injury.
Do not reach out too far. Keep your feet rmly on the
ground at all times. This will enable you retain control
over the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from the power
tool. Loose clothes, jewellery or long hair can become
entangled in the moving parts.
If there are devices for connecting dust extraction and
collection facilities, please ensure that they are attached
and used correctly. Using such devices can reduce dust-
related hazards.
POWER TOOL USE AND CARE
Do not expect the power tool to do more than it can. Use
the correct power tool for what you want to do. A power
tool will achieve better results and be safer if used in the
context for which it was designed.
Do not use the power tool if the switch cannot turn it on
and off. A power tool with a broken switch is dangerous
and must be repaired.
Disconnect the plug from the power source before
making adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store power tools, when not in use, out of the reach of
children and do not allow people who are not familiar with
the power tool or these instructions to operate it. Power
tools are potentially dangerous in the hands of untrained
users.
Maintenance. Check for misalignment or jammed moving
parts, breakages or any other feature that might affect
the operation of the power tool. If it is damaged, the
power tool must be repaired. Many accidents are caused
by using poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
jam and are easier to control.
Use the power tool, accessories and cutting tools, etc.,
in accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work which
needs to be done. Using a power tool in ways for which
it was not intended can lead to potentially hazardous
situations.
SERVICE
Your power tool should be serviced by a quali ed
specialist using only standard spare parts. This will
ensure that it meets the required safety standards.
ADDITIONAL SAFETY INSTRUCTIONS FOR
LASERS
Warning! The laser beam potentially causes eye
damage. Do not look or stare into the laser
beam.
During use, do not point the laser beam at people, directly
or indirectly through re ecting surfaces.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stomer SMS-1800-T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stomer SMS-1800-T in de taal/talen: Engels als bijlage per email.

De handleiding is 1,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info