- 9 -
Declaration of Guarantee
All rights are based on our guarantee period. We guar-
antee that your STEINEL Professional sensor product
will remain in perfect condition and proper working
order for a period of 5 years. We guarantee that this
product is free from material, manufacturing and
design flaws. In addition, we guarantee that all elec-
tronic components and cables function in the proper
manner and that all materials used and their surfaces
are without defects.
Making Claims
If you wish to make a claim, please send your product
complete and carriage paid with the original receipt of
purchase, which must show the date of purchase and
product designation, either to your retailer or contact
us at STEINEL (UK) Limited, 25 Manasty Road,
Axis Park, Orton Southgate, Peterborough, PE2 6UP,
for a returns number. For this rea- son, we recommend
that you keep your receipt of pur- chase in a safe
place until the guarantee period expires. STEINEL shall
assume no liability for the costs or risks involved in
returning a product.
For information on making claims under the terms of
the guarantee, please go to www.steinel-profession-
al.de/garantie
If you have a guarantee claim or would
like to ask any question regarding your
product, you are welcome to call us at
any time on our service hotline
01733 366700.
Declaration of conformity
This product complies with
- Low Voltage Directive 2014/35/EC
- EMC Directive 2014/30/EC
- RoHS Directive 2011/65/EC
- R&TTE Directive 1999/05/EC
Installation
Important: Make sure the installation site is not
subject to vibration.
Connection of a dimmer will damage the indoor
SensorLight.
1. Hold enclosure against the wall/ceiling and
mark drill holes, paying attention to any existing
wiring in the wall/ceiling.
2. Drill the holes, insert wall plugs (6 mm dia.).
3. Pierce sealing plug for power supply lead.
4. Pass power supply leads through.
5. Screw enclosure into place.
6. Connecting the mains power supply lead (see fig.).
The mains power supply lead is a 3-core
cable:
L = phase conductor (mostly black, brown or grey)
N = neutral conductor (usually blue)
PE = protective earth conductor (green/yellow)
If you are in any doubt, you must identify the cables
using a voltage tester; then disconnect from the power
supply again. Connect phase (L) and neutral conductor
(N) to the terminal. Insulate any PE protective earth
conductor in the power supply cable with adhesive
tape.
Technical specifications
Dimensions (H x W x D): 275 mm dia. x 95 mm
Material: Plastic (base), PMMA (shade)
Mains voltage: 220 – 240 V, 50/60 Hz
Output: 11 W LED / 620 lm / 56.4 lm/W
Colour temperature: 3000 kelvin (warm white)
LED life expectancy: 50.000 hours
HF-system: 5.8 GHz
Angle of coverage: 360° with 160° aperture angle also through glass, wood and stud walls
Detection reach: 1 m – 8 m all round
Twilight setting: 2 – 2000 lux
Time setting: 5 sec. to 15 min.
IP rating: IP 44
Protection class: II
IK rating: IK03
Intrinsic power consumption: < 0.5 W
Temperature range: -10° C to +40 °C
- 8 -
Important: Reversing the connections will result in a
short-circuit in the light unit or in your fuse box later
on. In this case, you must identify the individual con-
ductors once again and re-connect them. A mains
switch for switching the unit ON and OFF may of
course be installed in the mains power supply lead.
7. Set functions , , .
8. Fit light diffuser by turning it clockwise and
secure in place with the grub screw .
Surface wiring:
Surface wiring can be carried out as shown in
diagram I on page 2.
Note:
The sealing plugs must be fitted to attain the
IP rating.
GB
The indoor SensorLight can be put into service after
mounting the enclosure and connecting to the
mains power supply. When the light is turned ON
manually at the light switch, it switches OFF after
10 secs. for the calibration phase and is then activated
for operation in the sensor mode. It is not necessary to
actuate the light switch a second time.
Light-level setting (response threshold)
Factory setting: daylight operation (approx. 2000 lux)
The chosen response threshold
can be infinitely varied from
approx. 2 – 2000 lux.
Control dial = daylight operation (approx. 2000 lux)
Control dial = twilight operation (approx. 2 lux)
The control must be turned fully clockwise when
adjusting the detection zone and performing the walk
test in daylight.
Time setting (switch-OFF delay)
Factory setting: shortest time (approx. 5 sec.)
The light's ON time can be set to any
period from approx. 5 sec. and a
maximum of 15 min. Any movement
detected before this time elapses will
re-start the timer.
Control dial max. = longest time (approx. 15 min.)
Control dial min.= shortest time (approx. 5 sec.)
The shortest time setting is recommended when
adjusting the detection zone and performing a
functional test.
Note: After the light switches OFF, it takes approx.
1 sec. before it is able to start detecting movement
again. The light will only switch ON in response to
movement once this period has elapsed.
Reach setting (sensitivity)
Factory setting: max. reach (approx 8 m)
Reach is the term used to describe
the diameter of the more or less
circular detection zone produced on
the ground after mounting the
SensorLight at a height of 2.5 m.
Control dial max. = reach (approx. 8 m)
Control dial min. = reach (approx. 1 m)
Functions
Ø 1 m – 8 m
5 sec. – 15 min.
2 – 2000 lux
