622189
7
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
advantage because it will not accidentally drive a fastener
if the tool is contacted against the work - or anything else -
while the operator is holding the trigger pulled.
Before handling or operating this tool:
Read and understand the warnings contained in this manual.
Refer to the Tool Technical Data to identify the operating
system on your tool.
TOOL OPERATION CHECK
CAUTION: Remove all fasteners from tool before performing
tool operation check.
TRIGGER OPERATED TOOL:
A) With the finger off the trigger, hold the tool with a firm grip
on the handle.
B) Place the nose of the tool against the work surface.
C) Pull the trigger to drive a fastener. Release the trigger and
the cycle is complete.
Caution: The tool will cycle each time the trigger is pulled!
SEQUENTIAL TRIP OPERATION
A) Without touching the trigger, press the safety trip against
the work surface.
THE TOOL MUST NOT CYCLE.
B) Hold the tool off the work surface and, avoiding to point
the tool at self or others, pull the trigger.
THE TOOL MUST NOT CYCLE.
C) With the tool off the work surface, pull the trigger. Press
the safety trip against the work surface
THE TOOL MUST NOT CYCLE.
D) Without touching the trigger, press the safety trip against
the work surface then pull the trigger.
THE TOOL MUST CYCLE.
m TOOL USE
Having checked that the tool is working properly, press the
nose against the work piece and pull the trigger. Check
whether the fastener has been driven as required.
l If the fastener is not driven deep enough, increase the
air pressure by 5-6 psig. (0.5 Bar) at a time, checking the
result after each adjustment. Do not exceed the maximum
permissible working pressure (see Tool Technical Data)
l If the fastener is driven too deeply, reduce the air pressure
by 5-6 psig (0.5 Bar) at a time, checking the result after
each adjustment. Do not try to use less than the minimum
working pressure (see Tool Technical Data).
Always try to work with the lowest possible air pressure. This
will reduce the noise and vibration produced and will extend
the life of the internal components such as the bumper.
LOADING THE TOOL:
STHT1-12184 (APC-BN) & STHT1-12185 (APC-2IN1)
l Depress magazine release button and pull back magazine.
(Fig 1)
l With magazine fully open, insert fasteners. Points must be
against bottom of magazine. (Fig 2a & 2b)
l Push magazine forward. (Fig 3)
l Continue pushing until latch is engaged. (Fig 4)
STHT1-12183 (APC-FN)
l
Open the magazine: pull pusher back to engage latch. (Fig 1)
l With magazine fully open, insert fasteners from rear. Points
must be against bottom of magazine. (Fig 2).
l Close magazine: release latch by pulling latch tab and
pusher together slightly to disengage. Slide pusher against
the nails. (Fig 2 & 3)
FASTENER CONTROL ADJUSTMENT- STHT1-12184 (APC-BN) /
STHT1-12185 (APC-2IN1) / STHT1-12183 (APC-FN) (FIG 5)
Fastener control adjustment feature provides close control
of the fastener drive depth; from flush with the work surface
to shallow or deep counter sink. First, set the air pressure
for consistent drive in the specific work, then use the control
adjustment to give the desired depth of drive.
JAM RELEASE- STHT1-12185 (APC-2IN1) /
STHT1-12183 (APC-FN) (FIG 6).
Warning: Always disconnect the air before clearing a jammed
fastener.
1. Depress the latch button
2. With the latch button depressed, rotate the latch assembly
upwards and forwards until latch is on upward position.
3. Clear jam
ADJUSTING THE MULTI-DIRECTIONAL EXHAUST
STHT1-12185 (APC-2IN1) / STHT1-12183
(APC-FN) / STHT1-12184 (APC-BN) (FIG 7)
To adjust the multi-directional exhaust simply rotate the
exhaust deflector to the desired position as illustrated by the
arrows.
FT72124-a-0611_Tool_Manual_AW.indd 7 05/07/2011 17:01
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STHT1-12184 -APC-BN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STHT1-12184 -APC-BN in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info