622189
5
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
m SAFETY AND OPERATION MANUAL
Stanley tools are precision built. They will deliver efficient,
dependable service when used correctly and with care. As
with any fine power tool, the manufacturer’s instructions
must be followed for best results. Please study this manual
and understand the safety warnings and cautions before
operating the tool. The instructions on installation, operation
and maintenance should be read carefully and the manuals
kept for reference. Note: Additional safety measures may be
required because of your particular application of the tool.
Contact your Stanley representative or distributor with any
questions concerning the tool and it’s use.
NOTE:
Stanley tools have been designed to provide excellent
customer satisfaction and are designed to achieve maximum
performance when used with precision Stanley fasteners
engineered to the same exacting standards.
Stanley cannot assume responsibility for product
performance if any of our tools are used with fasteners
or accessories not meeting the specific requirements
established for genuine Stanley nails, staples and
accessories.
LIMITED WARRANTY
Stanley Inc., warrants to the original retail purchaser that this
product is free from defects in material and workmanship, and
agrees to repair or replace, at Stanley’s option, any defective
product within 90 days from the date of purchase. This
warranty is not transferable. It only covers damage resulting
from defects in material or workmanship, and it does not
cover conditions or malfunctions resulting from normal wear,
neglect, abuse or accident.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE
DURATION OF THIS WARRANTY.
STANLEY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Some countries do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights
which vary from state to state or from country to country.
To obtain warranty service, you must return the product at
your expense together with proof of purchase to a Stanley
regional warranty repair center.
SPECIAL REFERENCES
Only those fasteners that are specified in the operating
instructions (see Tool Technical data) should be used in the
tool. The tool and the specified fasteners are to be considered
as one single safety system for safety purposes.
Repairs shall only be carried out by the authorized agents of
Stanley or by other experts, giving due regard to the safety,
operating and maintenance instructions in this manual, the
specific tool manual and in the Tool Technical Data.
Note: Experts are those who, as a result of professional
training or experience, have acquired sufficient expertise in
the field of fastener driving tools as to be able to assess the
safe condition of fastener driving tools.
m SAFETY INSTRUCTIONS
EYE PROTECTION which
provides protection against
flying particles both from
the FRONT and SIDE should always be
worn by the tool operator and others in
the work area when loading, operating
or servicing this tool. Eye protection is
required to guard against flying fasteners
and debris, which could cause severe
eye injury. The employer and/or user must
ensure that proper eye protection is worn.
Eye protection in accordance with 89/686/EEC, and with
equal or greater grade than defined in EN166 should be
used. However all aspects of operators work, environment
and other type/s of machinery being used, should also
be considered when selecting any personal protection
equipment.
CAUTION: ADDITIONAL SAFETY PROTECTION may be
required in some environments. For example, the working
area may include exposure to noise levels that can lead to
hearing damage.
m
SAFETY INSTRUCTIONS FOR AIR SUPPLY AND CONNECTIONS
When connecting tools to the air supply, the fastener discharge
area of the tool should be pointed away from the operator and
others in the working area. Place the discharge area of the tool
over a test piece of material of sufficient thickness which will
fully accommodate the dimensions of the fastener to be driven.
With hands clear of the trigger and trip mechanism, limbs and
body clear of the discharge area the tool the air supply may now
be connected.
l
Do not use oxygen and combustible gases as an energy
source for pneumatically operated tools.
l
Do not use bottled gases or an air supply where the
maximum pressure in the line can potentially exceed 9.6
Bar as the tool may burst, possibly causing injury. If the
maximum air supply pressure could exceed these pressures,
then a pressure reducing valve with a downstream safety
valve shall be built into the air supply.
l
Do not pull the trigger or depress the safety trip while
connecting to the air supply. The tool could cycle, possibly
causing injury.
l
The connector on the tool must not hold pressure when the
air supply is disconnected. If a wrong fitting is used, the
tool can remain charged with air after disconnecting and
thus will be able to drive a fastener even after the air line is
disconnected possibly causing injury.
l
Always disconnect air supply: 1) Before making adjustments;
2) When servicing the tool; 3) When clearing a jam; 4) When
tool is not in use; 5) When moving to a different work area,
as accidental actuation may occur, possibly causing injury.
m SAFETY INSTRUCTIONS FOR LOADING TOOL
When loading the tool 1) Never place a hand or any part of the
body in fastener discharge area of the tool; 2) Never point the
tool at self or anyone else; 3) Do not pull the trigger or depress
the safety trip as accidental actuation may occur, possibly
causing injury.
GB
FT72124-a-0611_Tool_Manual_AW.indd 5 05/07/2011 17:01
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STHT1-12184 -APC-BN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STHT1-12184 -APC-BN in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info