720761
11
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
11
ENGLISH
(Original instructions)
u Remove the tool from the work surface before turning
the tool off. Allow the tool to stop rotating before laying
it down.
Do not use edge grinding/cutting wheels for surface grinding
applications because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and injury may result.
Using wire cup brushes and wire wheels
Wire wheels and brushes can be used for removing rust, scale
and paint, and for smoothing irregular surfaces.
Note: The same precautions should be taken when wire
brushng paint as when sanding paint.
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to work surface, allowing the tool
to operate at high speed. Material removal rate is greatest
when the tool operates at high speed.
u Maintain a 5˚ to 10˚ angle between the tool and work
surface for wire cup brushes.
u Maintain contact between the edge of the wheel and the
work surface with wire wheels.
u Continuously move the tool in a forward and back motion
to avoid creating gouges in the work surface. Allowing the
tool to rest on the work surface without moving, or moving
the tool in a circular motion causes burning and swirling
marks on the work surface.
u Remove the tool from the work surface before turning
the tool off. Allow the tool to stop rotating before setting
it down.
Use extra care when working over an edge, as a sudden
sharp movement of grinder may be experienced.
Precautions to take when wire brushing paint
u Wire brushing of lead based paint is NOT
RECOMMENDED due to the difculty of controlling the
contaminated dust. The greatest danger of lead poisoning
is to children and pregnant women.
u Since it is difcult to identify whether or not a paint
contains lead without a chemical analysis, we recommend
the following precautions when wire brushing any paint:
Personal safety
u No children or pregnant women should enter the work
area where the paint wire brushing is being done until all
clean up is completed.
u A dust mask or respirator should be worn by all persons
entering the work area. The lter should be replaced daily
or whenever the wearer has difculty breathing.
Note: Only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting masks
do not offer this protection. See your local hardware dealer for
the proper respiratory protection.
u NO EATING, DRINKING or SMOKING should be done
in the work area to prevent ingesting contaminated paint
particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or
smoking should not be left in the work area where dust
would settle on them.
Environmental safety
u Paint should be removed in such a manner as to minimize
the amount of dust generated.
u Areas where paint removal is occurring should be sealed
with plastic sheeting of 4 mils thickness.
u Wire brushing should be done in a manner to reduce
tracking of paint dust outside the work area.
Cleaning and disposal
u All surfaces in the work area should be vacuumed
and thoroughly cleaned daily for the duration of the
wire brushing project. Vacuum lter bags should be
changed frequently.
u Plastic drop cloths should be gatheredup and disposed
of along with any dust chips or other removal debris.
They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures.
During clean up, children and pregnant women should be
kept away from the immediate work area.
u All toys, washable furniture and utensils used by children
should be washed thoroughly before being used again.
Using cutting wheels
Do not use edge grinding/cutting wheels for surface grinding
applications because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and injury may result.
u Allow tool to reach full speed before touching tool to
work surface.
u Apply minimum pressure to work surface, allowing tool to
operate at high speed. Cutting rate is greatest when the
tool operates at high speed.
u Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage.
u Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before setting it down.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SFMCG400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SFMCG400 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 14,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info