720761
10
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
10
ENGLISH
(Original instructions)
Installing and Removing the Battery Pack from
the tool
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack (Fig. C)
u Insert battery pack rmly into tool until an audible click is
heard as shown in gure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
u Depress the battery release button (6b) as shown in
gure D and pull battery pack out of tool.
Storage hook (Optional extra) (Fig. E)
Warning! To reduce the risk of serious personal injury,
place the forward/reverse button in the lock-off position or
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, ensure
the screw (10) holding the storage hook is secure.
Note: When attaching or replacing the storage hook (9),
use only the screw (10) that is provided. Be sure to securely
tighten the screw.
If the hook is not desired at all, it can be removed from
the tool.
To move the storage hook, remove the screw (10) that holds
the storage hook (9) in place.
Note: Various trackwall hooks and storage congurations
are available.
Please visit our website www.stanley.eu/3 for
further information.
Fitting and removing the guard (Fig. F, G)
The tool is supplied with a guard intended for grinding
purposes. Ensure you use the correct guard specific for the
intended operation. If the unit is intended to perform cutting
off operations, a guard (16, Fig G) specific for this operation
must be fitted .
Fitting
u Place the tool on a table, with the spindle (11) facing up.
u Release the clamping lock (12) and hold the guard (5)
over the tool as shown.
u Align the lugs (13) with the notches (14).
u Press the guard down and rotate it counterclockwise to
the required position.
u Fasten the clamping lock (12) to secure the guard to
the tool.
u If required, tighten the screw (15) to increase the
clamping force.
Removing
u Release the clamping lock (12).
u Rotate the guard clockwise to align the lugs (13) with the
notches (14).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Switching on and off
u To switch on, slide the lock off switch (1) forward then
press and hold the trigger switch (2).
u To switch off, release the trigger switch (2).
Warning! Do not switch the tool on or off while under load.
Warning! Always slide the lock off switch (1) backwards to the
locked position when the tool is not in use.
Hints for optimum use
u Firmly hold the tool with one hand around the side handle
and the other hand around the main handle.
Surface grinding with grinding wheels
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to the work surface, allowing the
tool to operate at high speed. Grinding rate is greatest
when the tool operates at high speed.
u Maintain a 20˚ to 30˚ angle between the tool and
work surface.
u Continuously move the tool in a forward and back motion
to avoid creating gouges in the work surface.
u Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
Edge grinding with grinding wheels
Wheels used for cutting and edge grinding may break or kick
back if they bend or twist while the tool is being used to do
cut-off work or deep grinding. To reduce the risk of serious
injury, limit the use of these wheels with a standard
Type 27 guard to shallow cutting and notching (less than
13 mm in depth). The open side of the guard must be
positioned away from the operator. For deeper cutting with a
Type 1 cut-off wheel, use a closed Type 1 guard.
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to the work surface, allowing the
tool to operate at high speed. Grinding rate is greatest
when the tool operates at high speed.
u Position yourself so that the open-underside of the wheel
is facing away from you.
u Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage. Edge grinding wheels are not designed
to withstand side pressures caused by bending.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SFMCG400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SFMCG400 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 14,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info