720798
7
Verklein
Vergroot
Pagina terug
1/194
Pagina verder
7
GB
3 Button
Used to change temperature units from Fahrenheit to
Celsius.
When setting emissivity (
), high alarm value (HAL),
or low alarm value (LAL), press this button to
decrease the value to be set.
4 MODE Button
Each time you pull the trigger (for > 1 sec) to take
measurements, the thermometer records the maximum
(MAX), minimum (MIN), the differential (DIF) between the
maximum and the minimum, and the average (AVG) of
all readings taken during this pull. These data are stored
in memory and can be recalled with the MODE button
until you pull the trigger (> 1 sec) once more. When you
pull the trigger (> 1 sec) once more, all these data will
be erased from memory and the thermometer will start
a new recording.
When you pull and hold the trigger, the reading on
the main display will update every second with the
temperature of the target surface, and when you release
the trigger, the last reading is locked until you take new
measurement or the thermometer turns off automatically.
You can press the MODE button to display the maximum
(MAX), average (AVG), minimum (MIN), difference
(DIF), low alarm value (LAL) and high alarm value
(HAL) sequentially on the bottom display. The process is
illustrated in Figure A.
NOTE:
To read value correctly, please observe the bottom display
carefully to see whether the negative sign „-” and the
decimal point appear.
After you disconnect the battery from the thermometer for
a while, all the settings will be restored to default values
and all the recorded measurement data will be erased
from memory.
How to Set the Thermometer
Setting the High Alarm and Low Alarm
1. After the thermometer has been turned on, press and hold
down the MODE button until the symbol ashes, then
release the button.
2. Press the MODE button until LAL appears and ashes,
now the present low alarm value is being shown on the
bottom display.
3. Press the
button to decrease or the button to
increase the low alarm value.
NOTE: Press and hold down the
or button for
fast adjustment.
4. After setting the low alarm value, press the MODE button.
HAL ashes and the high alarm value is shown on the
bottom display. Use the same method of Step 3 to adjust the
high alarm value.
5. If the temperature of target surface reaches or is lower
than the low alarm value,
icon will appear and
ash and the built-in buzzer will beep and the LCD will
momentarily turn blue when you press and hold the trigger.
If the temperature of target surface reaches or is higher than
the high alarm value, icon will appear and ash and
the buzzer will beep and the LCD will momentarily turn red
when you press and hold the trigger.
6. At any time, you can press and hold down the MODE button
to exit setting mode.
NOTE:
Alarm accuracy is ± 1°C (or ± 2°F).
The low and high alarm values can be set only within the
thermometer’s measurement range.
The high alarm value must be higher than the low
alarm value.
Emissivity/ Setting Emissivity
Emissivity describes the energy-emitting characteristics of
materials. Most (90% of typical applications) organic materials
or non-shiny surfaces have an emissivity of 0.95 in the
default setting. Inaccurate readings will result from measuring
shiny or polished metal surfaces. To compensate, cover
the surface to be measured with masking tape or at paint.
Allow the tape or paint to reach the same temperature as the
surface it is covering. Then measure the temperature of the
covered surface.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FMHT0-77422 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FMHT0-77422 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 14,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info