604120
10
Verklein
Vergroot
Pagina terug
1/114
Pagina verder
8
EN
BP 750CE
- Impact drilling - for drilling masonry, concrete,
etc.
- Hammer mode - for chiselling and demolition.
For operation without fatigue during chiselling
and demolition, the accessory can be tted and
xed (at intervals of 8 degrees) in the desired
angular position (see “Changing the chisel posi-
tion”).
Turn the operation mode switch 6 to the desired
position:
(1) - Impact drilling
(2) - Changing the chisel position
(3) - Hammer mode
INSERTING OF SDS-MAX TOOL
Clean and grease the shank of the accessory,
before placing it into the socket!
Keep the locking socket 2 in upper (front) posi-
tion while inserting the tool.
Place the tool into the spindle without effort.
Rotate the tool until the grooves coincide.
After the grooves have coincided, push the tool
down (until the xing mechanism produces an
audible “click”). Check the proper xing of the
tool by pulling it strongly outwards.
WARNING: For operating with chisels
switch 6 shall always be in “hammer” posi-
tion.
REMOVING THE SDS-MAX TOOL
Pull the locking clutch entirely back and take the
tool out.
CHANGING THE CHISEL POSITION
- Insert the tool in the socket as it is described in
point “Inserting the SDS-max tool”.
- Turn the operating mode switch 6 in position
“Changing the chisel position”.
- Turn the tool by hand to the desired position.
- Turn the operating mode switch 6 in position
“hammer”, and then turn the tool slightly left wise
and right wise until it is locked.
Longer operation life of the rotary hammer and
higher efciency can be achieved only with well-
sharpened tools for demolition and chiselling.
AUXILIARY HANDLE
Always use the auxiliary handle.
Loosen the handle by turning it left wise. Turn
the handle in the most convenient for operation
position, and then tighten it well.
Do not carry the machine by a loose auxiliary
handle.
You can x the drilling depth through depth
gauge 4. The depth gauge 4 can be xed by
screw 3.
The auxiliary handle for these models is con-
nected to the body of the machine through vi-
bration dampers, protecting the operator and
reducing fatigue.
RECOMMENDATIONS FOR
OPERATION
Apply moderate pressure during operation (ap-
proximately 150-200 N)! Higher pressure will not
increase efciency when drilling and chiselling,
but it will lead to decreasing the operation life of
the machine.
Take the drill bit out of the opening from time to
time to remove dust.
Watch out for the stage of bit blunting and re-
place the bit when considerable decrease of ef-
ciency is observed.
ACCESSORIES
SDS-max twist drill bits for concrete Ø12 to
Ø50 mm. We recommend operation with Ø24
to Ø40 drill bits, for the optimum operation the
machine is designed for.
SDS-max break through drill bits for concrete
up to Ø80 mm
SDS-max core cutters up to Ø100 mm
SDS-max point chisels up to 600 mm long
SDS-max at chisels up to 80 mm wide
SDS-max groove chisel up to 32 mm wide
WARNING: We recommend using
these accessories or attachments when op-
erating your power tool. The use of any other
accessories or attachments might present a
risk of injury. Only use accessory or attach-
ment for its stated purpose. If you need any
assistance for more details regarding these
accessories, ask your local SPARKY service
centre.
VII - Maintenance
WARNING: Always ensure that the
tool is switched off and unplugged before
attempting to perform inspection or mainte-
nance.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sparky BP 750CE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sparky BP 750CE in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 1,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info