604120
9
Verklein
Vergroot
Pagina terug
1/114
Pagina verder
7
Original instructions
EN
This power tool is equipped with a
mechanism for reducing vibrations, decreasing
them by more than 30%.
PRIOR TO INITIAL OPERATION
Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
In case the work area is remote from the pow-
er source, use as short as practicable exten-
sion cord with proper cross-section.
Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING OFF
Switching on: Push and hold down switch 7.
Switching off: Release switch 7.
At low temperatures, demolishing with the pow-
er tool must begin only after it was operated for
about 3 minutes at no-load mode.
WARNING: Upon overloading the ma-
chine with 30% the red light-emitting diode 10
will glow. The machine must not be operated
conti nuously in this mode.
SELECTING THE SPEED, FREQUENCY
AND IMPACT ENERGY
Rotate the regulator 8 to choose a position
appropriate for the processed material. The
constant electronics maintain the speed, the
frequency and the impact energy constant, in-
dependently of the load, thus ensuring steady
operation mode. It is recommended to use the
operation modes listed in the table.
Rotate the regulator 8 from position A to position
F to increase the speed, the frequency and the
impact energy. The indicator 9 shall blink with
green light.
To choose High Power mode, rotate the regula-
tor 8 to position G. This mode is specied by in-
creased impact energy up to 13 J. The indicator
9 shall glow with constant green light.
WARNING: Using High Power mode
is recommen ded only when chiselling (ham-
mer mode), and for brief operation in impact
drilling mode. Continuous operation in impact
drilling mode shall result in operator’s quick
fatigue and increased wear-out of the ma-
chine.
SELECTING THE OPERATION MODE
The switching of operation modes can be per-
formed when the machine is not operating.
This rotary hammer can be used in two opera-
tion modes:
Application
Regulator
position
Rotation
speed
Impact rate
Single impact
energy
Render / Light construction
materials
A-B 120-145 min
-1
1150-1450 min
-1
4-5 J
Chiselling tiles C 175 min
-1
1700 min
-1
7 J
Bricks D 200 min
-1
1950 min
-1
8 J
Drilling in concrete E-F 225-250 min
-1
9-10 J
Chiselling concrete G 2800 min
-1
13 J
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sparky BP 750CE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sparky BP 750CE in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 1,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info