611458
104
Verklein
Vergroot
Pagina terug
1/202
Pagina verder
Vi3000 USER MANUAL
®
11.1 11.1: SOLO > PRIMARY BEHAVIOUR
11.0: SOLO System
AFL, PFL and SIP
The solo system on the Soundcraft Vi3000™ comprises a non-destructive PFL and AFL Solo capability from Inputs
and Outputs, and also the option of a destructive Solo-In-Place mode, for use only during soundchecks or rehearsals.
Solo-In-Place mode has to be enabled from within the Monitor Setup and changes the mode of operation of the Solo
System. It is automatically cancelled if the Monitor Setup screen is closed, to ensure that it cannot accidently be left
on.
PFL and AFL Soloing (SIP Mode OFF)
• Soloing a single Input locally generates a PFL or AFL Solo onto the Solo Bus, depending on the mode selected in the
Monitor Setup page (default is AUTO, see next point).
• If the Input Solo Mode is set to AUTO in the Monitor Setup page, soloing more than one Input locally (by pressing
and holding the rst Solo/Sel switch then pressing others, or switching off AUTO CANCEL mode) will generate an AFL
Solo onto the Solo Bus from all soloed Inputs. If a single output is soloed, the solo will be PFL.
• The PFL feed from Mono Inputs is taken after the channel Pan control so the signal heard on the Monitor outs will
reect the Pan setting. If the Input is a Stereo Input, the PFL feed is left channel to left Solo Bus, right to right.
• The AFL feed from Mono or stereo (paired) Inputs is stereo and follows the channel Pan.
• Soloing an Output (either locally or via a VCA Master Solo) generates an AFL or PFL Solo, depending on the mode
selected in Monitor Setup (default is AFL for outputs).
The post-fade Output signal is switched onto the Solo Bus.
• In all cases when SIP Mode is OFF, operation of any Solo will switch the audio onto the Solo Bus and the Monitor
section will be automatically switched so that the Solo audio replaces the previous monitor source selection (if any)
assuming that IN Solo and/or OUT Solo have been selected as a Monitor Source in the Monitor Setup Page.
Solo-In-Place Soloing (SIP mode ON)
• Soloing an Input generates a ‘destructive’ SIP Solo, actually muting or dimming all other Inputs which are not Soloed
or set to Mute Safe, as if you had pressed their channel ON switches. Other channels which are subsequently soloed
will be unmuted. The amount of dimming is controlled by the SOLO BLEND control on the front panel.
• Soloing an Input (or group of Inputs) by soloing a VCA Master that the input is assigned to, generates a SIP Solo on
all Inputs in the VCA Group.
* The Input signal is not switched onto the Solo Bus, and the Monitor section does not switch the Solo Bus audio to
override the monitor source selection (you hear the soloed signal(s) via the Master LRC busses directly.
• Soloing an Output generates a normal Output AFL or PFL Solo (according to the mode selection made in Monitor
Setup), the same as if SIP Mode was OFF. The Output signal is switched onto the Solo Bus and the Monitor section
switches so that the Output
Solo audio is heard on the Monitors, replacing the previous monitor source, if any.
SOLO SYSTEM BEHAVIOUR
104

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Soundcraft Vi 3000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Soundcraft Vi 3000 in de taal/talen: Engels als bijlage per email.

De handleiding is 17,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info