734406
50
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
ENGLISH
XENON 2 FF 50 Rev.3.0
COG, (Centre of Gravity), Setting
To carry out COG adjustment, there are basically 2 different options.
Adjustment can be carried out directly on the axle bracket (Standard
adapter only ) by shifting the crescent-shaped spacers from one side to
the other. To make an adjustment in larger steps, you must change the
position of the axle-stem on the frame.
NOTE:
COG Adjustments may lead to an unstable wheelchair, likely to tip.
This requires the use of anti-tip tubes.
An adjustment to the castor angle may be necessary when adjusting
the COG.
Changing the position of the axle stem
Using the quick-release axles, take the wheels out of the angle
adapter.
Undo both screws (1) and remove these completely. Fit the axle stem
in the desired position on the frame, put the screws back into the
perforated plate and then re-tighten the screws. When moving the axle
stem, also move the seat saddle on the frame, (change the axle stem
and the seat saddle). Make sure that the left and right sides are fitted
in the same positions. Use the given torque of 8 Nm (Fig.6.4.4 to
Fig.6.4.5).
COG setting on the standard axle bracket
Adjustment can be carried out directly on the axle bracket (standard
axle bracket only) by shifting the crescent-shaped spacers from one
side to the other. 3 Positions are possible (Fig.6.4.6 to Fig.6.4.8).
Using the quick-release axles, take the wheels out of the axle adapter
(4). Release the Allen screws (1) with an Allen key. Take the lid (2) of
the axle bracket off and arrange the crescent-shaped spacers (3)
according to your desired COG. Put the lid back on.
Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
NOTE: In case the axle adapter was moved or removed whilst ad-
justing the COG, wheel alignment and wheelbase width needs to be
checked and if necessary, adjusted (please refer to the "Wheel Align-
ment" section).
CAUTION!
Loctite ™ 243 thread locker MUST be used for re-mounting the Allen
screws (1) on the axle-adapter.
Fig.6.4.5
Fig.6.4.4
1
Fig.6.4.6
1
Fig.6.4.7
2
Fig.6.4.8
3 4
50

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sopur Xenon 2 FF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sopur Xenon 2 FF in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 2,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info