734406
49
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
ENGLISH
XENON 2 FF 49 Rev.3.0
6.4 Seating
Seat Sling
The seat sling can be adjusted for tension by using several straps. To
adjust the tension of the seat sling all straps have to be open. By pulling
the straps the tension of the seat sling will be tightened, (Fig.6.4.1).
NOTE: If the tension is too high, the cross brace will not be able to slide
into the saddle.
Adjusting the seat height:
Lightweight adapter
To change the seat height;
Remove the rubber bungs, (3) situated in the groove to the rear of the
axle stem.
Release the Allen screws (1) with an Allen key. Position axle bracket (2)
on the axle stem (4) according to the desired seat height (Fig.6.4.2).
In order to obtain the lowest possible seat height, the axle bracket can
be mounted upside down.
Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
Refit the rubber bungs.
Standard adapter
To change the seat height:
Remove the rubber bungs, (3) situated in the groove to the rear of the
axle stem.
Release the Allen screws (1) with an Allen key. Position axle bracket (2)
on the axle stem (4) according to the desired seat height (Fig.6.4.3).
Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
Refit the rubber bungs.
NOTE:
An adjustment to the castor angle may be necessary when adjusting
the rear seat height.
In case the axle adapter was moved or removed whilst adjusting
the seat height, wheel alignment and wheelbase width needs to
be checked and if necessary, adjusted (please refer to the "Wheel
Alignment" section).
CAUTION!
Some of the screws used during manufacturing are coated with thread-
locking fluid (blue dot on the thread) and can only be adjusted up to 3
times before they need to be replaced by new thread-locking screws.
Alternatively, the screws can be re-mounted using Loctite™ 243 thread
locker.
Loctite ™ 243 thread locker MUST be used for re-mounting the Allen
screws (1) on the axle-adapter.
Fig.6.4.1
Fig.6.4.3
2
3
1
4
Fig.6.4.2
3
1
2
4
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sopur Xenon 2 FF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sopur Xenon 2 FF in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 2,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info