The supplied rechargeable nickel-metal hydride battery is
not charged from the first time you use it. Be sure to
charge them before use.
About auto charge function
Placing the headphones on the transmitter automatically
turns them off, then charging starts. This eliminates the
need for turning on/off every time you wear and take off
the headphones.
If CHARGE/RED indicator does not
light up red
–Check if the right and left headphones are rested on the
transmitter correctly. Take off the headphones and place
them on the transmitter again so that the headphones’
contact points meet the transmitter’s contact pins.
–Charging may not be completed if the transmitter’s
contact pin and headphones’ contact point are dusty.
Wipe them with a cotton bud, etc.
Charging and usage time
Approx. charging timeMaximum usage time1)
7 hours2)20 hours3)
1) at 1 kHz, 0.1 mW + 0.1 mW output
2) hours required to fully charge an empty battery
3) Time may vary, depending on the temperature or
conditions of use.
To recharge supplied battery after
use
Place the headphones on the transmitter after use. The
CHARGE/RED indicator lights up red, then charging starts.
When charging is complete, there is no need to remove
the headphones from the transmitter.
Remaining battery
To check the remaining battery charge of the headphones,
turn on the POWER switch and check the POWER indicator.
The battery is still serviceable when the indicator lights up
green.
Charge the headphones if the POWER indicator turns off,
dims, flashes, or the sound becomes distorted or noisy.
Notes
–Insert the AC adaptor plug firmly.
–Be sure to use the supplied AC adaptor. Using AC
adaptors with different plug polarity or other
characteristics can cause product failure.
Unified
polarity plug
–The battery capacity may decrease if the headphones
are turned on and placed on the transmitter with the AC
adaptor disconnected.
–The transmitter automatically turns off while charging
the headphones.
–This system is designed to charge only the supplied
rechargeable battery BP-HP800-11 for safety. Note that
other types of rechargeable battery cannot be charged
with this system.
–If dry batteries are installed, they cannot be charged.
–Do not attempt to use the supplied rechargeable battery
BP-HP800-11 for other components. It is for use with this
system only.
–Charge in an environmental temperature of between
5 °C and 35 °C.
–When the battery life reduces to half, this may be the
end of battery lifetime. The supplied rechargeable
battery BP-HP800-11 is not commercially available. You
can order the battery from the store where you
purchased this system, or at your nearest Sony dealer.
–Do not touch the contact pins of the transmitter. If the
contact pins become dirty, charging may not be
possible.
–Charging may not be completed if the transmitter’s
contact pins and headphones’ contact points are dusty.
Wipe them with a cotton bud, etc.
Using the headphones
with separately-sold dry
batteries
Commercially available (LR03 (size AAA)) dry batteries can
also be used to power the headphones. Install two
batteries in the same manner as described in step 1 of
“How to use.”
If you attempt to charge the headphones with dry
batteries installed, the CHARGE/RED indicator lights up
red for 15 seconds, then turns off. The battery charge
function is not activated.
Battery life
BatteryApprox. usage time1)
Sony alkaline battery LR03
(size AAA)
24 hours2)
1) at 1 kHz, 0.1 mW + 0.1 mW output
2) Time may vary, depending on the temperature or
conditions of use.
Note
Do not carry a dry battery together with coins or other
metallic objects. It can generate heat if the positive and
negative terminals of the battery are accidentally come
into contact with metallic objects.
Tips for connection
–When you connect the stereo mini cable (stereo mini
jack) directly to an earphone jack (monaural mini jack),
the audio signal may not be output through the right
channel.
Tips for volume setting
–If you connect the transmitter to the headphone jack of
the A/V component, set the volume of the A/V
component as high as possible but not so high that the
audio signal becomes distorted.
–When watching videos, be careful not to raise the
volume too high in quiet scenes. You may hurt your ears
when a loud scene is played.
Tips for sound effect
Slide the switch to select the desired sound effect, OFF or
VOICE.
Position of
switch
Sound effect and suitable sound
source
OFFNormal playback of the
headphones.
VOICEProduces a clearer announcer’s
voice.
Notes
–The volume of the headphones may vary, depending on
the input signal and the setting of the EFFECT switch.
–The sound effect may not be obtained depending on
the input sound sources.
Tips for better reception
Receiving performance
This system utilizes very high frequency signals in the 800
MHz band so the receiving performance may deteriorate
due to the surroundings. The following examples illustrate
conditions that may reduce the reception range or cause
interference.
–Inside a building with walls containing steel beams
–An area with many steel file cabinets, etc.
–An area with many electrical appliances capable of
generating electromagnetic fields
–The transmitter is placed on a metal instrument.
–An area facing a roadway
–Noise or interfering signals exist in the surroundings due
to radio transceivers in trucks, etc.
–Noise or interfering signals exist in the surroundings
owing to wireless communication systems installed
along roadways.
Effective area of the transmitter
The optimum distance is up to approximately 100 m
without the system picking up some interference.
However, the distance may vary depending on the
surroundings and environment.
–If the system picks up some noise within the above
mentioned distance, reduce the distance between the
transmitter and the headphones, or select another
channel.
–When you use the headphones inside the effective area
of the transmitter, the transmitter can be placed in any
direction from the listener.
–Even within the signal reception area, there are some
spots (dead spots) where the RF signal cannot be
received. This characteristic is inherent to RF signals, and
does not indicate malfunction. By slightly moving the
transmitter, location of the dead spot can be changed.
Replacing the earpads
The earpads are replaceable. If the earpads become dirty
or worn out, replace them as illustrated below. The
earpads are not commercially available. You can order
replacements from the store where you purchased this
system, or at your nearest Sony dealer.
1 Remove the old earpad by pulling it out of the groove
on the housing.
2 Fit the new earpad in the groove of the housing.
Make sure the earpad is set to the vertical position.
Precautions
–When this system is not to be used for a long period of
time, disconnect the AC adaptor from the AC outlet
holding the plug, and remove the battery from the
headphones to avoid damage caused by battery
leakage and subsequent corrosion.
–Do not leave this system in a location subject to direct
sunlight, heat or moisture.
–You may hear some noise when you disconnect the AC
adaptor from the transmitter before taking off the
headphones.
–Avoid exposure to temperature extremes, direct sunlight,
moisture, sand, dust or mechanical shock.
–Please note that water does not splash, this product is
not waterproof specification.
Notes on headphones
To reduce the risk of hearing damage
Avoid using headphones at high volume. Hearing experts
advise against continuous, loud and extended play. If you
experience a ringing in your ears, lower the volume or
discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you
to hear outside sounds and to be considerate to the
people around you.
If you have any questions or problems concerning the
system that are not covered in this manual, please consult
your nearest Sony dealer.
Be sure to bring the headphones and the transmitter to
the Sony dealer when requiring repair work.
Troubleshooting
If you run into any problems using this system, use the
following checklist. Should any problem persist, consult
your nearest Sony dealer.
No sound/Low sound
–Check the connection of the A/V component or the AC
adaptor.
–Check that the A/V component is turned on.
–If you connect the transmitter to an A/V component
using the headphone jack, raise the volume level on the
connected A/V component within the range where the
sound is not distorted.
–Change the radio frequency with the CHANNEL selector
on the transmitter, then change the radio frequency to
that of the transmitter with the AUTO TUNING button on
the headphones.
–Use the headphones near the transmitter, or change the
position of the transmitter.
–Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still
off after charging, take the headphones to a Sony dealer.
–Raise the headphone volume.
The sound cuts off
–The transmitter turns off if no signal or low signal is
input for 4 minutes. If you connect the transmitter to an
A/V component using the headphone jack, raise the
volume level on the connected A/V component within
the range where the sound is not distorted.
Distorted or intermittent sound
(sometimes with noise)
–Use the headphones near the transmitter, or change the
position of the transmitter.
–Do not place the transmitter on a metallic table.
–If you connect the transmitter to an A/V component
using the headphone jack, lower the volume level on the
connected A/V component within the range where the
sound is not distorted.
–Change the radio frequency with the CHANNEL selector
on the transmitter, then change the radio frequency to
that of the transmitter with the AUTO TUNING button on
the headphones.
–Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still
off after charging, take the headphones to a Sony dealer.
Loud background noise
–If you connect the transmitter to an A/V component
using the headphone jack, raise the volume level on the
connected A/V component within the range where the
sound is not distorted.
–Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still
off after charging, take the headphones to a Sony dealer.
–Do not place the transmitter on a metallic table.
–Use the headphones near the transmitter.
The POWER/GREEN indicator flashes
green
–No signal or low signal is input. Start playback of the A/V
component, or raise the volume of the connected A/V
component within the range where the sound is not
distorted, otherwise the transmitter will turn off. If no
signal or low signal is input for about 4 minutes, the
transmitter turns off automatically.
Battery cannot be charged/
CHARGE/RED indicator flashes red,
or does not light up red
–Check that the right/left of the headphones and
transmitter correspond, and put the headphones on the
transmitter correctly.
–Install the supplied rechargeable nickel-metal hydride
battery. Dry batteries and rechargeable batteries other
than the supplied cannot be charged.
–If the CHARGE/RED indicator does not light up red even
though you put the headphones on the transmitter and
wait for a while, it may be the end of battery lifetime.
You can order the supplied rechargeable battery
BP-HP800-11 from the store where you purchased this
system, or at your nearest Sony dealer.
–Charging may not be completed if the transmitter’s
contact pin and headphones’ contact point are dusty.
Wipe them with a cotton bud, etc.
Short usage time (the supplied
rechargeable battery)
–Clean the + and − terminal of the supplied rechargeable
battery and the charging terminal of transmitter/
headphone with a dry cloth.
–Recharge the supplied rechargeable battery after the
fully discharged.
Specifications
RF stereo transmitter (TMR-RF895R)
Modulation FM stereo
Operating frequency
863.0 MHz – 865.0 MHz
Maximum output power
< 2.5 mW
Channel Ch1, Ch2, Ch3
Transmission distance
Approx. 100 m of longest
Audio inputs Stereo mini jack
Power requirements
DC 12 V (from the supplied AC adaptor)
Dimensions Approx. 130 mm × 273 mm × 160 mm
(w/h/d)
Mass Approx. 265 g
Rated power consumption
2.0 W
Operating temperature
5°C to 35°C
Wireless stereo headphones (MDR-
RF895R)
Frequency response
10 Hz – 22,000 Hz
Power source Supplied rechargeable nickel-metal
hydride battery BP-HP800-11, or
commercially available (LR03 (size AAA))
dry batteries
Mass Approx. 275 g
Operating temperature
5°C to 35°C
Included items
RF stereo transmitter TMR-RF895R
Wireless stereo headphones MDR-RF895R
AC adaptor (12 V) (1)
Rechargeable nickel-metal hydride battery
BP-HP800-11 (1)
Stereo mini cable (stereo mini plug), 1.5 m (1)
Card warranty (1)
Operating Instructions (this manual) (1)
Design and specifications are subject to change without
notice.
Svenska
Härmed försäkrar Sony Corporation att denna utrustning
överensstämmer med direktiv 2014/53/EU.
Den fullständiga texten till EU-försäkran om
överensstämmelse finns på följande webbadress:
http://www.compliance.sony.de/
Dansk
Herved erklærer Sony Corporation, at dette udstyr er i
overensstemmelse med direktiv 2014/53/EU.
Den fulde ordlyd af EU-overensstemmelseserklæringen er
tilgængelig på følgende internetadresse:
http://www.compliance.sony.de/
Suomi
Sony Corporation vakuuttaa, että tämä laite on direktiivin
2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen
teksti on saatavilla seuraavassa internetosoitteessa:
http://www.compliance.sony.de/
Norsk
Herved erklærer Sony Corporation at utstyrstypen er i
samsvar med direktiv 2014/53/EU.
EU-erklæring fulltekst finner du på Internett under:
http://www.compliance.sony.de/
Français
Le soussigné, Sony Corporation, déclare que cet
équipement est conforme à la Directive 2014/53/UE.
Le texte complet de la déclaration UE de conformité est
disponible à l’adresse internet suivante :
http://www.compliance.sony.de/
Deutsch
Hiermit erklärt Sony Corporation, dass diese Funkanlage
der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist
unter der folgenden Internetadresse verfügbar:
http://www.compliance.sony.de/
Español
Por la presente, Sony Corporation declara que este equipo
es conforme con la Directiva 2014/53/UE.
El texto completo de la declaración UE de conformidad
está disponible en la dirección Internet siguiente:
http://www.compliance.sony.de/
Nederlands
Hierbij verklaart Sony Corporation dat deze
radioapparatuur conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan
worden geraadpleegd op het volgende internetadres:
http://www.compliance.sony.de/
Italiano
Con la presente, Sony Corporation dichiara che questo
apparecchio è conforme alla Direttiva 2014/53/UE.
Il testo completo della dichiarazione di conformità UE è
disponibile al seguente indirizzo Internet:
http://www.compliance.sony.de/
Português
O(a) abaixo assinado(a) Sony Corporation declara que o
presente equipamento está em conformidade com a
Diretiva 2014/53/UE.
O texto integral da declaração de conformidade está
disponível no seguinte endereço de Internet:
http://www.compliance.sony.de/
Slovensky
Sony Corporation týmto vyhlasuje, že zariadenie je v
súlade so smernicou 2014/53/EÚ.
Úplné vyhlásenie EÚ o zhode je k dispozícii na tejto
internetovej adrese:
http://www.compliance.sony.de/
Slovenščina
Sony Corporation potrjuje, da je ta oprema skladna z
Direktivo 2014/53/EU.
Celotno besedilo izjave EU o skladnosti je na voljo na
naslednjem spletnem naslovu:
http://www.compliance.sony.de/
Česky
Sony Corporation tímto prohlašuje, že toto zařízení je v
souladu se směrnicí 2014/53/EU.
Úplné znění EU prohlášení o shodě je k dispozici na této
internetové adrese:
http://www.compliance.sony.de/
Magyar
A Sony Corporation igazolja, hogy ez a készülék megfelel a
2014/53/EU irányelvnek.
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a
következő internetes címen:
http://www.compliance.sony.de/
Български
С настоящото, Sony Corporation декларира, че това
оборудване е в съответствие с Директива 2014/53/EU.
Цялостният текст на ЕС декларацията за съответствие
може да се намери на следния интернет адрес:
http://www.compliance.sony.de/
Polski
Sony Corporation niniejszym oświadcza, że to urządzenie
jest zgodne z dyrektywą 2014/53/UE.
Pełny tekst deklaracji zgodności UE jest dostępny pod
następującym adresem internetowym:
http://www.compliance.sony.de/
Română
Prin prezenta, Sony Corporation declară că acest
echipament este în conformitate cu Directiva 2014/53/UE.
Textul integral al declarației UE de conformitate este
disponibil la următoarea adresă internet:
http://www.compliance.sony.de/
Ελληνικά
Με την παρούσα Sony Corporation δηλώνει ότι, αυτή η
συσκευή πληροί τους όρους της οδηγίας 2014/53/EU.
Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ
διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:
http://www.compliance.sony.de/
Connect the AC adaptor.Charge the headphones.
To AC
outlet
Connect the A/V component, following hookup or below.
Using the headphone jack of the A/V component
Stereo mini plug
Headphone jack
(Stereo mini jack)
TV, Digital music player, etc.
L (white)
R (red)
Stereo mini plug
Audio out
(L/R) jacks
Stereo system, Blu-ray Disc player, DVD player, TV*, etc.
* In case of no headphone jack.
If you cannot receive a clear audio signal
First change the radio frequency with the CHANNEL selector switch on the
transmitter, then briefly press the AUTO TUNING button on the headphones.
Noise Reduction process
The transmitter compresses the audio signal and converts it to RF signal. The headphones convert the received RF
signal to an audio signal and decompresses it. This process reduces noise picked up during transmission.
input signaloutput signal
decompression
compression
dynamic range
Transmitter unitHeadphones unit
RF transmission
noise level (low)
1
234
5
The transmitter compresses the audio signals dynamic range, then converts it to RF signal.
Noise may occur due to long distance transmission, etc.
The headphones convert the RF signal to an audio signal.
Noise may occur during conversion.
Decompression of the audio signals dynamic range reduces the noise level and improves the S/N (signal-to-noise)
ratio.
Adjust the volume.
Start playback of the A/V component.Wear the headphones.
Before listening
To reduce the risk of hearing damage, first lower the volume.
Tactile dot
UpDown
Tactile dot
Using the audio out (L/R) jacks of the A/V component
Use a connection cable (not supplied) between the transmitter and the A/V component.
If the sound is distorted by connecting the transmitter to the A/V component’s audio out (L/R) jacks, reconnect the transmitter to the headphone jack.
If the transmitter detects no signal or no sound, check the connection of the connected A/V components, then check the audio setting of the connected A/V components.
Insert the supplied rechargeable battery BP-HP800-11 into the left housing of the headphones.
Observe the correct polarity when installing battery.
Rechargeable nickel-metal hydride
battery BP-HP800-11 (supplied)
Insert the
end first.
(Green)
EnglishWireless Stereo Headphone System
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To reduce the risk of fire or electric shock, do not expose
this apparatus to dripping or splashing, and do not place
objects filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space, such as a
bookcase or built-in cabinet.
As the main plug of AC power adaptor is used to
disconnect the AC power adaptor from the mains, connect
it to an easily accessible AC outlet. Should you notice an
abnormality in it, disconnect it from the AC outlet
immediately.
CAUTION
Risk of explosion if the battery is replaced by an incorrect
type.
Do not expose the batteries (battery pack or batteries
installed) to excessive heat such as sunshine, fire or the
like for a long time.
Do not subject the batteries to extreme low temperature
conditions that may result in overheating and thermal
runaway.
Do not dismantle, open or shred secondary cells or
batteries.
Do not expose cells or batteries to heat or fire. Avoid
storage in direct sunlight.
In the event of a cell leaking, do not allow the liquid to
come in contact with the skin or eyes. If contact has been
made, wash the affected area with copious amounts of
water and seek medical advice.
Do not use any charger other than that specifically
provided for use with the equipment.
Secondary cells and batteries need to be charged before
use. Always use the correct charger and refer to the
manufacturer’s instructions or equipment manual for
proper charging instructions.
After extended periods of storage, it may be necessary to
charge and discharge the cells or batteries several times
to obtain maximum performance.
Dispose of properly.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
The AC Adaptor is not disconnected from the mains as
long as it is connected to the AC outlet, even if the unit
itself has been turned off.
High volume may affect your hearing.
The nameplate of transmitter is located on the bottom
exterior.
The nameplate of the headphones is located on the back
side of the slider.
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the
countries EEA (European Economic Area) and Switzerland.
Hereby, Sony Corporation declares that this equipment is
in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://www.compliance.sony.de/
Hereby, Sony Corporation declares that this equipment is
in compliance with the UK relevant statutory
requirements. The full text of the declaration of conformity
is available at the following internet address:
https://compliance.sony.co.uk
Disposal of waste batteries and electrical
and electronic equipment (applicable in
the European Union and other countries
with separate collection systems)
This symbol on the product, the battery or
on the packaging indicates that the
product and the battery shall not be treated as household
waste. On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical
symbol for lead (Pb) is added if the battery contains more
than 0.004% lead. By ensuring that these products and
batteries are disposed of correctly, you will help to prevent
potentially negative consequences for the environment
and human health which could be caused by
inappropriate waste handling. The recycling of the
materials will help to conserve natural resources. In case
of products that for safety, performance or data integrity
reasons require a permanent connection with an
incorporated battery, this battery should be replaced by
qualified service staff only. To ensure that the battery and
the electrical and electronic equipment will be treated
properly, hand over these products at end-of-life to the
appropriate collection point for the recycling of electrical
and electronic equipment. For all other batteries, please
view the section on how to remove the battery from the
product safely. Hand the battery over to the appropriate
collection point for the recycling of waste batteries. For
more detailed information about recycling of this product
or battery, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product or battery.
Notice for customers: the following information is only
applicable to equipment sold in countries applying EU
directives and/or UK applying relevant statutory
requirements
This product has been manufactured by or on behalf of
Sony Corporation.
EU and UK Importer: Sony Europe B.V.
Inquiries to the EU Importer or related to product
compliance in Europe should be sent to the
manufacturer’s authorized representative, Sony Belgium,
bijkantoor van Sony Europe B.V., Da Vincilaan 7-D1, 1930
Zaventem, Belgium.
Inquiries to the UK Importer or related to product
compliance in the UK should be sent to the manufacturer’s
authorized representative, Sony Europe B.V., The Heights,
Brooklands, Weybridge, Surrey KT13 0XW, United Kingdom.
This equipment has been tested and found to comply with
the limits set out in the EMC regulation using a connection
cable shorter than 3 meters.
The unit is not waterproof. If water or foreign objects enter
the unit, it may result in fire or electric shock. If water or a
foreign object enters the unit, stop use immediately and
consult your nearest Sony dealer. In particular, be careful
in the following cases.
–When using the unit around a sink, etc.
Be careful that the unit does not fall into a sink or
container filled with water.
–When using the unit in the rain or snow, or in humid
locations
–When using the unit while you are sweaty
If you touch the unit with wet hands, or put the unit in
the pocket of a damp article of clothing, the unit may
get wet.
Note on static electricity
Static electricity accumulated in the body may cause mild
tingling in your ears. To reduce the effect, wear clothes
made from natural materials, which suppress the
generation of static electricity.
For details on the effect of contact to the human body
from the mobile phone or other wireless devices
connected to the unit, refer to the instruction manual of
the wireless device.
This product (including accessories) has magnet(s) which
may interfere with pacemakers, programmable shunt
valves for hydrocephalus treatment, or other medical
devices. Do not place this product close to persons who
use such medical devices. Consult your doctor before
using this product if you use any such medical device.
Checking the included
items
RF stereo transmitter
TMR-RF895R (1)
AC adaptor (1)
Wireless stereo
headphones MDR-RF895R
(1)
Stereo mini cable (stereo
mini plug), 1.5 m (1)
Rechargeable nickel-metal
hydride battery BP-
HP800-11 (1)
Features
Thank you for purchasing the Sony MDR-RF895RK
Wireless Stereo Headphone System. Before operating the
unit, please read this manual thoroughly and retain it for
future reference.
Some features are:
–Wireless system that allows you to listen to a
programme free the restriction of a cable
–Up to 100 meters reception range*
–High fidelity sound reproduction
–New mode “VOICE” for clear hearing of personal voice
range
–Noise reduction system to reproduce a clear sound with
minimum transmission noise
–Comfortable fit
–Smooth and Comfortable Earpads
–Long playback time (maximum 20 hours)
–Easy recharging function with secure charging
mechanism
–Rechargeable Battery
–Automatic tuning on headphones for optimum signal
reception
–3 transmission channels available
–Volume control function and sound effect function on
the headphones
* Transmission distance varies depending on conditions of
use
(Red)(Off)
Complete when indicator
turns off.
Check the CHARGE/
RED indicator lights
up red.
4
23
After use
Turn off the power of the headphones.
About sending RF signals
The transmitter starts sending RF signals automatically
when it detects an audio signal from the connected
component. Note that;
–Noise may occur depending on the transmitter position
and room conditions. It is recommended to place the
transmitter in a location that produces the clearest
sound.
–If the transmitter is placed on a metallic table, you may
hear noise, or the reception range may decrease. Do
not place on a metallic table.
If no signal or low signal is input
for about 4 minutes
When no signal is input for about 4 minutes, the
transmitter turns off automatically*. The POWER indicator
of the transmitter blinks for 4 minutes, then turns off. The
transmitter restarts after receiving an audio signal again.
The transmitter may also turn off if low signal is input for
about 4 minutes. In this case, raise the volume of the
connected A/V component within the range where the
sound is not distorted, then lower the volume of the
headphones.
* If signal noise is output from the connected A/V
Op de linker oorstuk kun je, na het naar binnen kantelen, het moeilijk te lezen woord "push" zien staan. Goed drukken en het is open. Bij mij lukt het goed.
Geantwoord op 17-12-2020 om 16:16
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Sony MDR-RF895RK bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Sony MDR-RF895RK in de taal/talen: Engels, Frans als bijlage per email.
De handleiding is 1,56 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
