680783
58
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
58
S10931-00001_Rev-D_EN
11. Connections and special functions of the wall
control unit
Installing the keypad
1. When installing the potential-free keypad, select
a suitable position at a height of at least 1.6 m.
2. Install the keypad.
3. Route the keypad cable to the wall control unit and
secure it firmly to prevent displacement.
Installing the control cable and settings on the
wall control unit
1. Disconnect the operator from the mains voltage.
Check it is disconnected from the power supply.
2. Unscrew the light cover from the wall control unit
and remove it upwards. Hold the front cover firmly
while doing so.
3. Remove the control unit cover gently towards
the front and unplug the connection cable for
the membrane keypad from the wall control unit,
see chapter "7.3 Light and control unit cover of
the wall control unit."
4. If an accumulator is used, it must also be
disconnected, see Chapter "11.12 Installing and
removing the accumulator."
5. Remove the control unit cover.
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
G
N
D
+24
V
ON
1234
Fig. 6 Fig. 7
6. Connect the cable of button 2 to the terminal block
for COM and Signal.
Button 2 is connected.
7. Set DIP switch 4 on the wall unit to "ON."
8. Plug in the connection cable for the button and
for the accumulator, if necessary.
9. Close the ceiling control unit in reverse order,
see chapter "11.12 Installing and removing the
accumulator" and "7.3 Light and control unit
cover of the wall control unit."
10. Supply the operator with the mains voltage.
Check that the power supply is connected.
Settings on the motor carriage
To determine the partial opening door position, the
following settings must be made on the motor carriage.
1. Close the door completely up to the door CLOSE
end position.
2. Open the motor carriage, see chapter "7.1 Cover of
the motor carriage."
3. Set DIP switch 2 on the motor carriage to "ON."
4. Press button 2 for the partial opening function.
The door moves in door OPEN direction.
5. Press button 2 again for the desired position for
stopping.
The door stops at the desired position.
11.6 Deleting partial opening
1. Set DIP switch 2 on the motor carriage to "OFF."
2. Open the door completely up to the door OPEN
end position.
Partial opening is deleted.
To program a new position, see chapter "10.17 Setting
partial opening."
11.7 Photocell and frame photocell
A 2-wire photocell from SOMMER or a 4-wire photocell
can be connected to the control unit. The control unit
automatically detects which version it is and sets itself
to that version.
Fig. Terminal for a 2-wire photocell
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
Fig. Terminal for a 4-wire photocell
INFORMATION
If a photocell is retrotted on
a programmed system, the control
unit must be reset, see chapter
"10.13 Performing a reset."
58

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9110 pro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9110 pro in de taal/talen: Engels als bijlage per email.

De handleiding is 10,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9110 pro

Sommer S 9110 pro Gebruiksaanwijzing - Nederlands - 88 pagina's

Sommer S 9110 pro Gebruiksaanwijzing - Deutsch - 88 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info