680556
58
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
58
46900V001_Rev-D_EN
12. twin operation
9. Programme the handheld transmitters for the
respective operators, see Chapter "10.4 Explanation
of the radio channels" and "10.5 Programming the
transmitter".
INFORMATION
Only one handheld transmitter can
be assigned per function. Undesired
malfunctions could otherwise occur.
12.4 Partial opening
One partial opening can be programmed for each of
the two operators (master and slave). Programming or
deletion is performed as for the standard equipment,
see Chapter "10.17 Setting partial opening" and
"10.18 Deleting partial opening".
Example:
Master on radio channel CH 2 (partial opening) on
handheld transmitter button 3. For the slave, on radio
channel CH 2 (partial opening) on handheld transmitter
button 4.
Wired
The COM input and signal on the ceiling control unit can
be used for this purpose. DIP switch 4 on the ceiling
control unit must be ON.
The input is then no longer available for connection of a
photocell.
Mode of operation
If button 2 (partial opening) is activated, the master
receives the partial opening command. See also chapter
"10.17 Setting partial opening".
12.5 Defined opening and closing
The functions Defined opening and closing of the
operators (master and slave) can only be configured via
the CH 3 and CH 4 radio channels. These settings are
not available when corded or via the Conex accessory
part.
12.6 Door status display
If DIP switch 2 on the ceiling control unit is set to ON,
the relay is activated during door movement and when
the door is open. It remains activated until both operators
(master and slave) are again at the door CLOSE end
position.
12.7 Lighting for twin operation
The lighting can be switched on and off for the selected
operator via the respective handheld transmitter. This
also applies for the connected supplemental lighting, see
also Chapter "10.16 Setting the lighting function".
12.8 Photocell
Optionally, a photocell can be connected. The photocell
must be configured in such a way that it can be aligned
to cover two doors. If the photocell is interrupted, the
operator of the moving door reverses. See also chapter
"11.6 Photocell and frame photocell".
INFORMATION
If a photocell is retrotted on a
programmed system, the control unit must
be reset, see Chapter "10.13 Resetting the
control unit."
12.9 External button
With the Conex additional circuit board, both operators
(master and slave) can be operated in pulse sequence
mode. Fit the Conex as described in the separate
instructions. Set DIP switch 1 on the ceiling control unit
to ON.
Mode of operation
Button 1 - master
Button 2 - slave
12.10 Reset
The slave becomes the master again when a factory
reset is carried out. The operator must be configured as
the slave again via SOMlink and a WiFi-enabled device,
see Chapter "12.3 Selecting and configuring master
and slave".
58

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9110 base plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9110 base plus in de taal/talen: Engels als bijlage per email.

De handleiding is 8,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9110 base plus

Sommer S 9110 base plus Installatiehandleiding - Nederlands - 80 pagina's

Sommer S 9110 base plus Installatiehandleiding - Deutsch - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info