680556
57
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
57
46900V001_Rev-D_EN
12. twin operation
12.1 twin operation
Two operators can be controlled with a control unit,
for example in a double garage with two garage doors
Both operators are connected to one control unit for
this purpose.
2
1
Fig. Installation example for twin operation, slave (1) and
master (2)
Mode of operation
If one of the operators receives a command and starts to
move, the other operator is locked for this time. The other
operator can only be started after the movement has
stopped.
INFORMATION
Both operators cannot be operated at the
same time.
12.2 Installing the operators
The installation of the operators is described here using
an example.
INFORMATION
Master and slave are assigned regardless
of the installation.
1. Install the operators on the two doors as described in
the Chapter "6. Installation".
Insert the control unit into one track.
Insert the plug-in unit with the connection cable into
the other track.
12.3 Selecting and configuring master
and slave
Requirements
Both operators are configured as a master in the factory
settings. The main communication to the control unit is
effected via the master.
INFORMATION
No automatic closing function and no
energy-saving mode possible in twin
operation.
1. Set DIP switches 1 and 3 on the ceiling control unit
to ON.
2. Connect the ceiling control unit to the mains voltage.
Check that the power supply is connected.
3. Configure the operator with the ceiling control unit (1)
as the slave. A connection to the motor carriage
can be established via SOMlink and a WiFi-enabled
device for this purpose.
4. In the menu, under the "twin operation“ settings,
configure "Operator is slave” for the selected
operator and save the entry. Check the entry.
5. Disconnect the ceiling control unit from the mains
supply for 15 seconds.
GND
+24V
gn
rt
+
-
Fig. Connection of chain and track for both operators to the
control unit
Terminal block Function
gn + Track
rt - Chain
6. Connect the operator without the ceiling control unit,
the master (2), to the ceiling control unit parallel
to the terminal block for chain (rt) and track (gn).
The connection cable must be firmly secured to
prevent displacement.
7. Reconnect the control unit to the mains voltage.
8. Put both operators into operation successively, see
Chapter "9. Commissioning", "10. Connections
and special functions of the motor carriage" and
"11. Connections and special functions of the
ceiling control unit".
57

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9110 base plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9110 base plus in de taal/talen: Engels als bijlage per email.

De handleiding is 8,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9110 base plus

Sommer S 9110 base plus Installatiehandleiding - Nederlands - 80 pagina's

Sommer S 9110 base plus Installatiehandleiding - Deutsch - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info