658836
33
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
Operating and maintenance information - Maintenance and care of the cutting gear
ENGLISH 33
E
N
G
Sharpening the saw chain
Just like any other cutting tool, the saw chain is subject to natural wear. Your chainsaw will only be
able to deliver its full potential if the saw chain is correctly sharpened.
Symptoms of a blunt saw chain or one which has been sharpened incorrectly:
o Poor cutting performance and floury chippings ! the saw chain is blunt.
o Chip size too small ! The depth limiter spacing is too small.
o Chip size too large and increased kickback tendency ! The depth limiter spacing is too large.
o Saw pulls to one side while cutting ! The saw chain is not evenly sharp.
o Visually apparent damage to the cutting surfaces.
Experience is needed to correctly sharpen the saw chain. If you are unsure, have the saw chain
checked by a specialist workshop and re-sharpened as required. The information provided below is
intended for experienced users or specialist workshops.
A special round chain file with the correct diameter should be used for sharpening. Normal round files
are not suitable.
Chain - code Pitch in inches Files Ø mm/inches Filing angle α Depth limiter spacing b mm/inches
21BP… .325’’ 4,8 /
3
/
16
30° 0,64 / .025
21LP... .325’’ 4,8 /
3
/
16
25° 0,64 / .025
73LP… 3/8’’ 5,5 /
7
/
32
25° 0,64 / .025
73D, DP… 3/8’’ 5,5 /
7
/
32
35° 0,64 / .025
Filing direction: 10° upw Filing direction: 0° horizon
21BP…, 21LP…,73LP… 73D, DP…
A file holder makes guidance of the file easier, as it has
markings for the correct sharpening angle (align the
markings parallel to the saw chain) and limits the
penetration depth (4/5 of the file diameter)
Position the file holder on the roof of the tooth. The file should only engage
during the forward stroke. Lift the file off when moving it back.
The shortest cutting tooth is sharpened first. The length of this tooth is then the
target size for all the other teeth on the saw chain. All of the cutting elements
must have the same length.
To start with, file all of the cutting elements on one side from the inside
outwards, then file all of the cutting elements on the other side.
Always fully file out any damage from the side plate or the roof of the tooth.
Correction of the depth limiter:
The distance b between the depth limiter (round nose) and the cutting edge defines
the thickness of the chips. The best cutting results are obtained with the prescribed
depth limiter spacing, which should be checked every time the saw chain is
sharpened.
Lay the depth limiter gauge on the cutting element. If the depth limiter protrudes,
file off the protruding part with a flat file.
Round off the front edge of the depth limiter. The original shape must be restored.
CAUTION: If the spacing is too large then there is a greater risk of
kickback.
For your safety: If you would like to pull the chain through while filing, pull the chain forwards
with a screwdriver towards the tip of the rail. This will reduce the risk of slipping.
α
33

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Solo-644

Zoeken resetten

  • Hallo!
    Ik heb een Solo 644 kettingzaag. Nu lekt die benzine. Op de aanzuigleiding zit een verdikking die in de opening naar buiten komt. Waarschijnlijk zit die niet meer op de juiste plaats. Hoe kom ik eraan of plaats ik een nieuwe aanzuigleiding? Gesteld op 1-3-2023 om 16:00

    Reageer op deze vraag Misbruik melden
  • Hallo,
    Solo 644 is een hele tijd niet gebruikt
    en start .. heeft wel voldoende compressie
    altijd mengsmering gebruikt,
    mvgr. erlenhofe@hotmail.com
    Gesteld op 23-1-2021 om 10:17

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 644 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 644 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info