799214
10
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
English
SEWING MACHINE
SW8231
USE AND CARE:
- 
- Do not use the appliance if the accessories attached to it are defective.
Replace them immediately.
- Never run the machine when there’s thread in the needle, but no fabric
on the machine. This could damage the machine.
- Always keep your hands away from the needle, hand wheel, upper
thread tension dial and pattern selection dial when the appliance is
running.
- 
the sewing machine needle.
- Never sew with a damaged needle plate as this can cause needle to
break.
- Do not use bent needles
- 
causing it to break.
- Never drop or insert any object into any opening.
- 󰀨
- Use the appliance handle/s, to catch it or move it.
- Disconnect the appliance from the mains when not in use and before
undertaking any cleaning task.
- Unplug the appliance from the mains before replacing any accessory.
- This appliance is for household use only, not professional, industrial
use.
- Store this appliance out of reach of children and/or persons with physi-
cal, sensory or reduced mental or lack of experience and knowledge.
- Keep the appliance in a dry, dust-free place, out of direct sunlight.
- Make sure that dust, dirt or other foreign objects do not block the fan
grill on the appliance.
- Keep the appliance in good condition. Check that the moving parts are
not misaligned or jammed and make sure there are no broken parts or
anomalies that may prevent the appliance from operating correctly.
- Use the appliance and its accessories and tools in accordance with
these instructions, taking into account the working conditions and the
󰀨
those intended could result in a hazardous situation.
- Never leave the appliance unattended while in use.
DESCRIPTION
Front view:
1 Take up lever
2 Upper thread tension dial
3 Pattern selection dial
4 Thread cutter
5 Light
6 Needle clamp screw
7 Bpttp, bobbin
8 Drawer
9 Hand wheel
10 Reverse button
11 Selector switch.
󰀨
11.b. manual (Vel 1/ Vel 2)
Back view:
1 bobbin winder pin
2 Bobbin winder stop
3 Foot pedal input
4 Bobbin winder tension disk
5 Presser foot lifter
6 Presser foot
7 Dc input
If the model of your appliance does not have the accessories described
above, they can also be bought separately from the Technical Assis-
tance Service.
INSTRUCTIONS FOR USE
Before use:
- Make sure that all the product’s packaging has been removed.
- Some parts of the appliance have been lightly greased. Consequently,

After a short time, this smoke will disappear.
- Prepare the appliance according to the function you wish to use:
Using the foot pedal and adaptor
- Connect the foot pedal by inserting the jack into the foot pedal input
socket. Then you can use the foot pedal turn on the machine instead
󰀨
and convenient.
- Connect the adaptor’s jack to the DC input socket (7) on the back of
the machine, and connect the plug to the main power supply.
- CAUTION: make sure the foot pedal is unplugged from the machine
when you’re not using it, so the sewing machine won’t accidentally
start up.
Needle replacement
- 󰀨󰀨
kind of fabric, just follow these steps.
- CAUTION: To prevent injury from accidentally starting up the machine,
󰀨-
tor plug.
- 1. Turn the hand wheel to raise the needle to its highest position. Hold
the old needles and loosen the needle clamp screw. Remove the old
needle and discard responsibly (Fig.1).
- 
correct direction (to the back). Be sure to push the needle completely
into the clamp before tightening the needle clamp screw.
- 3. Tighten the needle clamp screw.
- CAUTION: Needle direction must be correct and be sure to tighten the
thimble screw, to avoid needle fall by accident.
Threading upper THREAD
- 1. Turn the hand wheel to raise the needle to its highest position
- 2. Put a spool on the thread spindle, put on the thread spindle cover
and then pull out the thread.
- 3. Pull the thread and let it passes through the bobbin winder tension
disk
- 4. Guide the thread through the hole in the chromed lever and pull
straight down towards the needle.
- 5. Feed the thread throught the hole in the chromed lever and pull
straight down towards the needle.
- 6. Feed the thread through the hole in the needle holder, then through
the eye of the needle from the front side to the back and pull out 10
cm to the back.
- 󰀨
supply and remove the foot pedal when threading the machine.
Presser foot replacement
Removing the presser foot
- Turn the hand wheel counterclockwise to raise the needle to its highest
position.
1
2
3
4
5
6
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solac SW8231 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solac SW8231 in de taal/talen: Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 2.88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info