621561
65
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
65
v1.06
Admin and Installation Guide M700, M300 Description of Settings
Network
Setting Description
IP settings
DHCP/Static IP Allowing changes in protocol for getting a dynamic IP address. When DHCP is
enabled, the other IP settings and options are not available.
DHCP enabled: IP addresses are allocated from a pool of available addresses.
Static IP: IP addresses are manually assigned by the network administrator.
Default: DHCP.
IP address Enter when using static IP address. Not accessible when using DHCP.
Subnet mask Enter when using static IP address. Not accessible when using DHCP.
Default gateway Enter IP address of your router when using static IP address. Not accessible
when using DHCP.
DNS (Primary) Enter DNS server address of Internet service provider when using static IP
address. Not accessible when using DHCP.
DNS (Secondary)
VLAN Settings The VLAN settings can be used on a managed network with separate Virtual
LANs (VLAN) for sending voice and data trac. To work on these networks,
the base station can tag voice trac it generates on a specic "voice VLAN"
using the IEEE 802.1q specication.
ID 12-bit identication of the 802.1Q VLAN. Permitted value(s): Decimals 0 to
4094. A VLAN ID of 0 is used to identify priority frames and the ID of 4095
(i.e., FFF) is reserved. If 0 is set, there is no VLAN tagging or VLAN discovery
through DHCP.
Default: 0.
User priority 3-bit value dening user priority. Values are 0 (best eort) and 1 to 7 (lowest
to highest priority). The values can be used to prioritize dierent classes of
trac (voice, video, data, etc.).
Default: 0
Synchronization If enabled, the VLAN ID is automatically synchronized between the base
stations in a multicell chain. They will be automatically rebooted during the
synchronization.
Default: Disabled.
DHCP Options
Plug-n-play If enabled: DHCP option 66 is used to automatically provide PBX IP address to
base station.
Default: Disabled.
NAT Settings
Enable STUN Default: Disabled. Enable to use STUN.
STUN server Permitted value(s): IPv4 values or URL. Currently only IPv4 is supported.
STUN bindtime determine Default: Disabled.
STUN bindtime guard Time in seconds. Permitted values: Positive integers.
Default: 80.
Enable RPORT Default: Disabled. Enable to use RPORT in SIP messages.
Keep alive time The interval in seconds at which the base station sends a keepalive signal to
the SIP server to maintain NAT bindings. Permitted values: Positive integers.
Default: 90.
65

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Snom M300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Snom M300 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Snom M300

Snom M300 Gebruiksaanwijzing - Deutsch - 82 pagina's

Snom M300 Gebruiksaanwijzing - English - 44 pagina's

Snom M300 Gebruiksaanwijzing - English - 38 pagina's

Snom M300 Gebruiksaanwijzing - English - 58 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info