621561
63
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
63
v1.06
Admin and Installation Guide M700, M300 Description of Settings
Setting Description
Attended transfer behavior Depending on whether the PBX requires the second call to be active (i.e., not
on hold) before the REFER is sent, this setting denes whether pressing the
"Transfer" function key on a handset will put the second call on hold.
Setting "Hold 2nd Call": Pressing the transfer key puts the second call on hold
before REFER is sent.
Setting "Do Not Hold 2nd Call": Pressing the transfer key results in sending of
REFER without rst putting the second call on hold.
Default: Hold 2nd Call
Use own codec priority This setting species whether the incoming call's codec priority (setting:
disabled) or the system's own codec priority (setting: enabled) will be used
for the call.
Default: Disabled
DTMF signaling This setting species how the decimal digits (and ‘*’ and ‘#’) are converted
into sounds that share similar characteristics with voice to easily traverse
networks designed for voice.
SIP INFO: Carries application-level data along SIP signalling path (for
example: DTMF digits generated during SIP session or DTMF tones via data
packets in the same internet layer as the voice stream, etc.).
RFC 2833: DTMF handling for gateways, end systems, and RTP trunks (e.g.:
Sending DTMF tones via data packets in dierent internet layer as the voice
stream).
Both: Enables SIP INFO and RFC 2833 modes.
Default: RFC 2833
DTMF payload type This setting allows the user to specify a value for the DTMF payload type /
telephone event (RFC2833).
Default value: 101
Remote Caller ID Source
Priority
SIP information eld used for Caller ID source. Options:
PAI - FROM
FROM
ALERT_INFO - PAI - FROM
Enable blind transfer This setting species whether blind transfer of calls is allowed (enabled) or
not.
Default: Enabled
Codec priority This setting species the codec priority for audio compression and
transmission. After changing the order of priority with the Up/Down buttons,
click on Reset codes.
NOTE: In a multicell setup, you must also go to the multicell page and click on
Reboot chain in order to update the handsets in the multicell installation.
Options: G.722; G.711A-law, �-law; G.726
NOTE:
With G.722 in the list, the codec negotiation algorithm is active. This causes
the handset setup time to be slightly slower than when G.722 is removed
from the list.
With G.722 as rst priority, the number of simultaneous calls per base station
will be reduced from 10 (8) to 4 calls.
RTP packet size This setting species the packet size oered as preferred RTP packet size
during RTP packet size negotiation.
Default value: 20 ms
63

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Snom M300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Snom M300 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Snom M300

Snom M300 Gebruiksaanwijzing - Deutsch - 82 pagina's

Snom M300 Gebruiksaanwijzing - English - 44 pagina's

Snom M300 Gebruiksaanwijzing - English - 38 pagina's

Snom M300 Gebruiksaanwijzing - English - 58 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info