427103
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
- loosen wing nut F and raise depth gauge G to desired
cutting depth plus value noted earlier (7 + 35 = 42 mm)
- tighten wing nut F
! always check the adjusted routing depth on a
piece of scrap wood
Adjusting depth stop turret
For making repetitive cuts at depth intervals of 5 or 10
mm rotate turret H 2 so that desired depth stop J clicks
into place right under depth gauge G
Mounting adapter plate (for copying with a template) 5
Mounting/removing of vacuum cleaner adapter K 6
Mounting rip fence 7
- insert rip fence rods L through holes in base-plate M
- slide rip fence to desired width and fasten it with
2 wing nuts N
Operating the tool 8
- adjust routing depth
! always hold the tool firmly with both hands
- place tool on workpiece
- switch on the tool by pushing switch P in "I" position
! before the router bit reaches the workpiece, the
tool should run at full speed
- loosen handle E and slowly push tool down until depth
gauge G reaches depth stop J
- tighten handle E
- carry out the routing procedure with uniform feed rate
- use the tool with its base-plate flat on the workpiece
- as a general rule one should pull the tool, not push it
- after finishing the work, loosen handle E and guide the
tool back into the upper starting position
- switch off the tool by pushing switch P in "O" position
Proper guiding 9
- keep in mind that router bit turns clockwise
- guide tool so that bit turns into the workpiece, not
away from it
APPLICATION ADVICE
Use the appropriate router bits 0
For cuts parallel with the side of your workpiece use rip
fence
For making parallel cuts in a workpiece far from the
edge 8
- fasten a straight piece of wood on the workpiece by
means of 2 clamps
- guide tool with base-plate along edge of wood which
now functions as a rip fence
When using bits with a pilot or ball bearing, the pilot or
ball bearing should slide along the edge of the workpiece
which should be perfectly smooth !
For larger routing depths, it is recommended to carry out
several repetitive cuts with lower removal rates
GUARANTEE / ENVIRONMENT
Always keep tool and cord clean (especially the
ventilation slots Q 8)
! disconnect the plug before cleaning
Lubricate sliding bars R 2 occasionally
This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
Dispose of the tool by sorting tool, accessories and
packaging for environment-friendly recycling (the plastic
components are labeled for categorized recycling)
Défonceuse 1845
INTRODUCTION
Loutil est conçu pour le fraisage des rainures, bords,
profils et rainures droites dans le bois, les matières
plastiques et matériaux de construction légers ainsi que
pour le fraisage par copiage
SPECIFICATIONS TECHNIQUES 1
SECURITE
GENERALITES
Lisez et conservez ce manuel d'instructions (faites en
particulier très attention aux instructions de sécurité au
dos de ce manuel)
Cet outil est interdit aux jeunes n'ayant pas atteint l'âge
de 16 ans
Toujours débranchez l’outil avec tout réglage ou
changement d’accessoire
ACCESSOIRES
SKIL ne peut se porter garant du bon fonctionnement de
cet outil que sil a été utilisé avec les accessoires
dorigine
La vitesse admissible des accessoires utilisées doit être
au moins aussi élevée que la vitesse à vide maximale de
loutil
Ne jamais utilisez des fraises endommagées ou
déformées
Nutilisez que des fraises bien affûtées
Protégez les accessoires contre les impacts, les chocs et
la graisse
Nutilisez que des fraises en acier rapide (HSS) ou au
carbure avec cet outil
AVANT L'USAGE
Faites attention aux vis, clous ou autres éléments qui
pourraient se trouver dans la pièce à travailler et qui
risqueraient dendommager très fortement votre outil;
d'abord les enlevez puis travaillez
Toujours contrôlez si la tension secteur correspond à la
tension indiquée sur la plaquette signalétique de loutil
(les outils conçus pour une tension de 230V ou 240V
peuvent également être branchés sur 220V)
Ne jamais travaillez avec des matériaux contenant de
l'amiante
F
6
XP SKIL 1845 21-03-2003 15:31 Pagina 6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 1845 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 1845 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info