427103
5
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
Router 1845
INTRODUCTION
The tool is intended to route grooves, edges, profiles and
elongated holes in wood, plastic and light building
materials as well as to copy-route
TECHNICAL SPECIFICATIONS 1
SAFETY
GENERAL
Read and save this instruction manual (pay special
attention to the safety instructions at the back)
This tool should not be used by people under the age of
16 years
Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
SKIL can assure flawless functioning of the tool only
when original accessories are used
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
Do not use damaged or deformed router bits
Only use sharp router bits
Protect accessories from impact, shock and grease
Only use high speed steel (HSS) or carbide-tipped (CT)
router bits with this tool
BEFORE USE
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
Do not work with materials containing asbestos
Clamp the workpiece in case it does not remain
stationary from its own weight
Do not clamp the tool in a vice
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
The noise level when working can exceed 85 dB(A);
wear ear protection
Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials to
be worked on
Be sure tool is switched off when plugging in
DURING USE
Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
Never use tool when cord or base-plate M 2
(=protective guard) is damaged; have it replaced by a
qualified person
Keep hands and fingers away from router bit when tool is
switched on
Never exceed maximum cutting depth of router bit
(= B 0) while cutting
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
In case the router bit is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
In case of current interruption or when the plug is
accidentally pulled out, immediately put the on/off switch
in the O-position in order to prevent uncontrolled
restarting
Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
After finishing the work, loosen handle E 2, guide the
tool back into the upper starting position, and switch off
the tool
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
Mounting/removing router bits 3
! switch off the tool and disconnect the plug
! ensure that router bit shaft is perfectly clean
! ensure that collet size corresponds with shaft size
of router bit
- turn tool upside down
- lock shaft by pushing shaft lock A (rotate collet nut B,
if necessary) and hold it while you
FOR MOUNTING:
- loosen collet nut B with wrench C
- insert bit 3/4 in collet D
- tighten collet nut firmly with wrench C
FOR REMOVING:
- loosen collet nut B with wrench C
- pull bit out of collet D
- release shaft lock A
! for loosening router bit it may be necessary to tap
collet nut with wrench 4
! never tighten collet nut, if there is no router bit in
collet; collet may be damaged
Changing collet 3
! switch off the tool and disconnect the plug
! ensure that collet shaft is perfectly clean
- turn tool upside down
- remove collet nut B (lock shaft)
- pull collet D out of collet nut B
- insert new collet in collet nut B until it snap-locks
- mount collet nut B (lock shaft)
Adjusting routing depth 2
EXAMPLE
Desired routing depth 7 mm
- loosen handle E
- loosen wing nut F so that depth gauge G moves freely
- push tool down until router bit is in contact with
workpiece and tighten wing nut F
- note value as indicated on depth scale (e.g. 35 mm)
(for zeroing)
GB
5
XP SKIL 1845 21-03-2003 15:31 Pagina 5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 1845 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 1845 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info