777999
14
Verklein
Vergroot
Pagina terug
1/67
Pagina verder
14 GB/IE/NI
Place the thinning attachment 12 onto the pro-
duct as described in the chapter “Changing
the attachments.“
Note: The thinning attachment 12 prevents
every hair from being cut.
Trimming beards
Note that the desired trim length can only be
achieved if the product is held perpendicularly
to the skin‘s surface.
Comb the beard using the supplied comb 17
in its direction of growth.
Shorten the beard downwards from the ear to
the chin, one side after the other.
Use the cutting unit 1 without the comb attach-
ment 11 to trim the beard very short or to trim
a moustache or hairline.
Graduate the desired trim length by rotating
the lower part of the product 5 according to
length position indicator 4. The trim length
may be set to 5 different levels (0.8 mm/
1.1 mm/1.4 mm/1.7 mm/2.0 mm).
To trim a moustache, firstly comb it straight
downwards. Begin in the centre above the
mouth, then one side and then the other.
Cleaning and care
CAUTION! DANGER TO LIFE BY ELECTRIC
SHOCK! Pull the plug-in mains adapter 7 out
of the mains socket before cleaning the product.
Never touch the plug-in mains adapter 7 with
moist or wet hands, especially when you plug
it into the socket or pull it out of the socket.
Always keep the plug-in mains adapter 7 and
supply cord dry.
CAUTION! RISK OF PROPERTY DA
MAGE!
Do not submerge the product in water or any
other liquid to clean it as the product is not
waterproof. This could damage the live parts
(rechargeable batteries).
Do not use any corrosive or abrasive cleaning
agents.
Clean the housing and the charging base 6
using a damp cloth and a mild detergent.
Switch the product off by pressing the ON/
OFF button 3 b once or twice, until the indicator
light 3 a goes off.
Disconnect the supply cord from the product
and remove the plug-in mains adapter 7 from
the mains socket.
Remove the comb attachment 11 , the thinning
attachment 12 or the cutting unit 1 from the
product (see Fig. G + H).
Wash the comb attachment 11 , the thinning
attachment 12 or the cutting unit 1 with run-
ning water if necessary.
Dry the comb attachment 11 , the thinning
attachment 12 or the cutting unit 1.
Remove the cutting unit 1 (see Fig. H).
Remove any remaining bits of hair from the
cutting unit 1 using the cleaning brush 13
provided (see Fig. I).
Apply one or two drops of blade oil 14
between the blades and the moving parts
(see Fig. J).
Adjust the length position indicator 4 to
2.0 mm after you have finished cleaning the
product, before once more attaching the
cutting unit 1 to the product (see Fig. K).
Note: Clean the cutting unit 1, comb attach-
ment 11 and thinning attachment 12 after
every use.
Storage
Place the product in the charging base 6 if
you wish to store it. Alternatively, you can also
store it in the travel case 16 provided.
Troubleshooting
Error Cause Solution
The product
does not
work.
The battery
may not be
charged.
Recharge the
product.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Silvercrest SHBS 700 A1 - IAN 354063 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Silvercrest SHBS 700 A1 - IAN 354063 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens als bijlage per email.

De handleiding is 1.53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info