759464
10
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
- 10 - 08/2020
Copyright © 2020, Fast ČR, a.s.
CONTROLLING THE VACUUM CLEANER USING THE MOBILE
APPLICATION
The vacuum cleaner can also be controlled using a smartphone or tablet. The
application enables you to select the cleaning mode, stop the cleaning process or
send the vacuum cleaner to the charging station; it provides an overview of how much
time was spent cleaning and about the condition of the vacuum cleaner.
The application is freely available in the Apple App Store or Google Play Store. The
link for this application is found in the picture part of this user'smanual.
Note:
The robotic vacuum cleaner supports Wi-Fi in the 2.4 GHz frequency band.
If unsure about which standards are used by your Wi-Fi network and your
router, please contact your internet service provider or the manufacturer
of the router.
After downloading and installing the application on to asmart device, set the vacuum
cleaner into the network configuration mode by pressing and holding down button
A2 until abeep is made. The indicator of button A2 will start flashing slowly. If you
wish to cancel the network configuration mode, press button A2 on the vacuum
cleaner or C4 on the remote control.
Launch the application. After registration, the application will guide you through the
process for connecting the vacuum cleaner to your Wi-Fi network.
CHARGING THE ROBOTIC VACUUM CLEANER
AUTOMATIC CHARGING
When the vacuum cleaner finishes cleaning or when it detects alow battery voltage
during operation, the indicator in button A2 will start flashing read and the vacuum
cleaner will automatically start to seek out the charging station.
In order for it to find it and dock, it needs to find the infrared signal transmitted
by the charging station. For this reason, we recommend leaving the charging
station constantly connected to the power grid and located in accordance with the
instructions provided in chapter LOCATION OF THE CHARGING STATION.
In the event that the vacuum cleaner is for some reason unable to find the charging
station (too many obstacles, incorrect location, etc.) the indicator in button A2 will
start flashing red. In this case, it is necessary to place the vacuum cleaner near the
charging station or directly on to its contacts.
After docking in the charging station, the charging cycle will commence. Afull charge
takes approximately 5 hours. The actual charging time depends on the power level of
the battery. Afully charged battery will provide up to 90 minutes of operation.
During the charging process, the indicator light in button A2 will flash white. When the
battery is fully charged, the indicator lights on both buttons will remain permanently
lit white and the process will end automatically.
In the event that the charging contacts are disconnected during the charging cycle,
the vacuum cleaner will move away from the charging station and then re-dock itself
to resume the charging process, unless it is prevented from doing so by an obstacle. In
the event of apower outage, the charging cycle will be interrupted and will continue
after the power supply is renewed. In the event that the maximum charging current is
exceeded, the charging station will automatically interrupt the charging cycle.
MANUAL CHARGING
If the vacuum cleaner is located away from the charging station and detects a low
battery voltage then the indicator in button A2 will start flashing red. Press button C2
on the remote control. The vacuum cleaner will automatically seek out the charging
station and start automatic charging as described in the previous chapter.
If the battery is so flat that the vacuum cleaner is unable to seek out the charging
station then it is necessary to dock the vacuum cleaner into the charging station by
hand. Pick up the vacuum cleaner and manually place it into the charging station so
that the charging contacts on the underside of the vacuum cleaner and the charging
contacts on the charging station are connected. When the contacts are connected,
charging will start.
CARING FOR THE BATTERY
We recommend that you do not interrupt the charging cycle and maintain the battery
in acharged state.
Do not leave the vacuum cleaner completely flat for an unnecessarily long period of
time. Abattery that is allowed to remain flat for along time may self-discharge below
apermissible level and thereby cause irreparable damage to itself.
REPLACING THE BATTERY
Make sure that the vacuum cleaner is turned off with the main switch A7. Turn the
vacuum cleaner upside down and remove the screws from the battery cover A14.
Take off the cover.
Disconnect the battery and take it out. Connect a new batter and place it into the
battery compartment being careful not to damage the connector cables. Screw the
battery cover back on.
Attention:
Use only the original battery type.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE AND SOLUTION
The vacuum cleaner
cannot be turned on.
The battery is almost or completely flat, and it is necessary
to charge it. Manually place the vacuum cleaner on to the
charging station.
The vacuum cleaner
is running but it is
vacuuming dust and
dirt poorly or not at all.
The dust container is full. Empty it out.
The dust filter in the container is not properly installed or
is excessively soiled. Check the position and cleanliness of
the filter.
The central rotary brush is clogged with material or hair is
tangled on it, and it is not turning. Clean out the brush and
the suction hole.
The vacuum cleaner
is making an unusual
noise while cleaning.
The central rotary brush, side rotary brushes or one of the
motorised wheels is wrapped with material or tangled into
an obstacle (cables, etc.).
The vacuum cleaner
travels only backwards
when it is turned on.
The vacuum cleaner was placed on afloor that is too dark.
Move the vacuum cleaner to alighter-coloured floor and
start it again.
One of the bottom sensors is soiled. Clean the all the sensors.
The bristles on arotary
brush are deformed
and do not sweep up
dust and dirt.
The bristles are worn out. Dip them in warm water to renew
their original shape. Contact the vendor or service centre and
order anew brush.
Cleaning at
ascheduled time
didnot occur.
The battery was not sufficiently charged. Scheduled cleaning
will only start when the battery is charged to at least 30%.
The vacuum cleaner was turned off using the main switch.
After performing scheduled cleaning, it must be in the stand-
by or sleep mode.
The vacuum cleaner
did not travel on to the
charging station.
The charging station is not connected to mains power.
Connect it.
The vacuum cleaner is too far away from the charging
station. Carry the vacuum cleaner by hand to the vicinity of
the charging station.
The charging station is not located according to the
instructions in this user'smanual and the vacuum cleaner has
poor access to it.
The vacuum cleaner is
in the charging station
but is not charging.
Check that the charging station is connected to the power
grid. Clean the charging contacts on the charging station and
the vacuum cleaner.
Check that the main power switch is in the ON position.
The vacuum cleaner
did not connect to the
Wi-Fi network.
Weak Wi-Fi network signal or the vacuum cleaner is out of
its range.
Incorrectly entered password.
Your router transmits in the 5 GHz broadcast band but your
vacuum cleaner can only receive signals in the 2.4 GHz
broadcast band.
Indicator of button A2
is flashing red
The control system of the vacuum cleaner has detected
aproblem, that may include the vacuum cleaner being lifted
off the ground, the dust container / water tank sliding out of
the vacuum cleaner during the charging process, the wheels
or brushes becoming blocked during operation, etc. Attempt
to identify what has caused the problem and attempt to fix it.
If the red flashing persists, try turning off the vacuum cleaner
using the main switch A7 and turn it back on after at least
20seconds. If even this fails to help, contact an authorised
service centre.
CLEANING AND MAINTENANCE
Prior to cleaning, always turn off the vacuum cleaner by setting the main switch A7
to the OFF position.
For cleaning, never use abrasive cleaning products, solvents, etc.
Neglecting cleaning and maintenance may negatively affect the working order of the
vacuum cleaner and lead to its reduced performance.
Attention:
When turning the vacuum cleaner upside down for maintenance
tasks, ensure that it does not fall out of your hands on to the floor
or that you do not damage its camera A5 when putting it down.
We recommend placing the vacuum cleaner on to asuitable soft
surface.
DUST CONTAINER AND DUST FILTER
Empty out the dust container after every use and clean it regularly.
Pressing latch E1, slide out the dust container A6 from the vacuum cleaner and take it to
awaste basket, garbage bin, etc.
Press latch E6 to open the bottom cover E5 and tip out the dirty material. For hygiene
reasons, we recommend that you tip out the dirty material away from living areas.
Open the cover E4 and take it out of the holder with the dust filter E3. Tap out the dust
filter and its holder or clean these parts using the brush E2. Check the condition of the
filter and if damaged, replace it with anew one.
In the event of greater soiling, the dust container and the holder can be completely
washed under running water. After washing them, it is necessary to allow all the
components to dry completely.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SRV 8550 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SRV 8550 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info