Handleiding Scheppach SC36 (pagina 19 van 120) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds, Fins)

782005

Verklein

Vergroot

Pagina terug

1/120

Pagina verder

19 GB

Operation

To prevent accidental start-up of the equipment, the

push-bar (Fig. 1 / Item 1) is equipped with a safety

lock-off (Fig. 1 / Item 2) which must be pressed before

the lever switch (Fig. 1 / Item 1) can be pressed. If the

lever switch is released, the equipment switches off .

Repeat this process several times so that you are

sure that the machine functions properly. Before you

perform any repair or maintenance work on the ma-

chine, ensure that the cutting unit is not rotating and

that the power supply is disconnected.

Important!

Never open the ejector ap when the motor is run-

ning. A rotating cutting unit can cause injuries. Al-

ways fasten the ejector ap carefully. The ap ips

back to the “Closed” position by the tension springs!

Always ensure that a safe distance (provided by the

long handles) is maintained between the user and the

housing. Be especially careful when scarifying and

changing direction on slopes and inclines. Maintain a

solid footing and wear sturdy, non-slip footwear and

long trousers. Always scarify along the incline (not up

and down). For safety reasons, the scarier may not

be used to scarify inclines whose gradient exceeds

15 degrees.

Use special caution when backing up and pulling the

scarier (tripping hazard)!

Tips for proper working

It is recommended that you overlap scarifying paths

a little.

Try to scarify in straight lines for a nice, clean look.

Insodoing, the aeration swaths should always overlap

each other by a few centimeters in order to avoid bare

strips.

As soon as grass clippings start to trail the scarier, it

is time to empty the grass basket.

Danger! Before taking off the grass basket,

switch off the motor and wait until the roller has

come to a stop.

To remove the grass basket, lift up the ejector ap

with one hand, while unhooking the basket with the

other.

How frequently you should scarify your lawn is de-

termined primarily by the speed at which the grass

grows and the hardness of the soil. Keep the un-

derside of the equipment clean and remove soil and

grass build-up. Deposits make it more difcult to start

the aerator and decrease the quality of the scarify-

ing. Always scarify along inclines (not up and down).

Switch off the motor before doing any checks on the

roller.

Montage

n Important!

You must fully assemble the appliance before

using it for the rst time!

Guide rail assembly (Fig. 3 - 8)

• Loosen the grip screw on the height adjustment

(9).

• Fit the lower handles (8) as shown in Figures 4+5.

Make sure that the springs (4a/4b) go into the op-

posite groove respectively

• Subsequently tighten the grip screw again (Fig. 5).

• Connect the upper push bars (3) with the middle

push bar (6) and the two lower push bars (8). To

do this, use four tensioning levers (5), fastening

screws (5a) and washers (5b). (Figs. 6+7)

• Fasten the switch cable with the two cable clamps

Installing the catch basket

• Slide the catch basket (7) over the frame for the

catch basket and put the rubber tabs over (Fig. 9,

10)

• Hang the catch basket (7) into the device. To do

this, lift the discharge ap (11a) and hang the catch

basket (7) into the appropriate brackets on the de-

vice. (Fig. 11)

Adjusting the scarifying depth (Fig. 12)

The scarifying depth is set using the depth adjust-

ment (10) on the two front wheels. To do this, gently

pull the depth adjustment (10) away to the left, bring

it to the desired position and let it latch into that posi-

tion.

+1 = Drive / or transport position

0 = 0 mm

-1 = Scarifying depth -5 mm

-2 = Scarifying depth -10 mm

-3 = Scarifying depth -15 mm

Adjusting the aerator roller depth

In order to guarantee faultless operation and avoid

damage to the aerator roller, only use the aerator

roller with the depth setting “O”.

Adjusting the steering bar (Fig. 5 + 13)

• First loosen the grip screws (Fig. 5), so that you

can adjust the steering bar.

• Set the desired height, as shown in Fig. 13. (You

can choose between three levels).

Replacing roller (Fig. 14, 15)

ATTENTION! Be sure to wear gloves!

Remove the Allen screws and lift the roller on this

end. Pull the roller in the direction of the arrow, out

of the drive square. Slide the new roller in the direc-

tion of the arrow back into the drive square and then

press it into the bracket. Use the Allen screws to fas-

ten the roller back onto the housing.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scheppach SC36 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info