782088
13
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
emission values add up to a total below the underlying
work conditions mentioned in ISO 7904 Appendix A.
Sound power level in dB (Work)
Idle speed LWA = 89 dB (A)
Processing LWA = 98.5 dB (A)
Sound pressure level at the workstation in dB
Idle speed LpAeq = 85.5 dB (A)
Processing LpAeq = 92 dB (A)
Sound power level in dB (Thickness)
Idle speed LWA = 107 dB (A)
Processing LWA = 108 dB (A)
Sound pressure level at the workstation in dB
Idle speed LpAeq = 94 dB (A)
Processing LpAeq = 94.5 dB (A)
The specified values are emission values and therefore do
not have to represent exact work station values at the same
time. Although there is a correlation between emission and
immission gages, it is not possible to determine reliably,
whether additional precautions are necessary or not. Cur-
rent factors of the work station affect the immission gages,
including the characteristics of the work station, other
sound sources, for example number of machines other ad-
jacent operations. The permissible work values can vary
from country to country. However, the operator should ca-
pacitate the information, in order to make an estimate of
the hazard and risk.
In these operating instructions we‘ve marked the sections that
pertain to your safety with this sign:
General safety instructions
Training of the operator
Pass on the safety warnings to all people who will work
on the machine.
The operator must be at least 18 years old. Apprentices
must be at least 16 years old and can only work on the
machine under supervision.
Persons operating the machine should not be distract-
ed.
• Keep children away from machines connected to the
power system.
Wear well-fitting clothes. Take off all jewelry, rings and
wristwatches.
Follow all safety and danger warnings on the machine
and keep them in legible condition.
Caution while working: risk of injury to fingers and hands
by the rotating cutting tool.
Stability assurance
During assembly, please make sure that the planing ma-
chine stands firmly on solid ground.
Utilization in accordance with the regulations
The planing machine is constructed exclusively from of-
fered tools and supplies for wood processing.
The machine complies with the valid EG machine guide-
lines.
The machine is designed for one shift of work, power-on
time S1
Follow all safety and danger warnings on the machine.
• Keep all safety and danger warnings on the machine
complete and legible.
When using in an enclosed space, the machine must be
attached to an extraction unit.
To extract the wood shavings or sawdust, the machine
must be attached to an extraction unit. The velocity of
flow of the connection piece of the extraction unit must
be 20 m/s. Negative pressure 1200 Pa.
When operating in a commercial area, a deduster must
be employed during extraction.
Do not disconnect or remove the extraction unit or the
deduster while the machine is running.
Use the machine only when it is in technically sound
conditions, as well as in compliance with the law, with
awareness of safety and danger according with the op-
erating instructions! Eliminate immediately all unneces-
sary distraction that could compromise safety!
The safety, operation and maintenance instructions of
the manufacturer, as well as the dimensions given in the
technical specs, must be observed.
The applicable accident prevention regulations and oth-
er technical safety rules of general knowledge must be
observed.
The machine must be used, maintained or repaired
only by a competent person who can be trusted and is
informed of the dangers. The manufacturer will not be
responsible for damages resulting from arbitrary altera-
tions to the machine.
The machine should only be used with the original tools
and supplies from the manufacturer.
• All use beyond the instructions counts as noncompli-
ance with the regulations. The manufacturer does not
carry any responsibility for damages resulting from such
use, the operator will bear all risks on his own.
Assembly
Part of scope of delivery:
1 Hook wrench 5,5/7
1 Hex head wrench SW 3
1 Hex head wrench SW 4
1 Hex head wrench SW 6
1 Hex head wrench SW 8
Due to technical reasons, your packed planing machine is not
fully assembled.
The planing machine shouldn‘t be lifted onto the work ta-
ble!
Setup and adjustment, Fig. 1
The machine stands on 4 adjustable rubber cushions.
Balance the unevenness of the floor. Loosen the lower
hexagon nut using the key and turn the rubber cushions
correspondingly in and out.
Tighten the hexagon nut again. (secure the hexagon nut)
Attention!
Be sure to align the machine by using a level.
If the rubber cushions are displaced, the machine can be
bolted into the boreholes in the floor.
For utilization with a base frame, dismantle the rubber
cushions and screw on the frame.
Planer fence, Fig. 2, Fig.3
Attach the planer fence to the machine.
Set the position to 90° with the help of a stop angle.
Tighten the release handle
The planer fence is continuously variably pivoting from 90°
english 11
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Plana 4.0 C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Plana 4.0 C in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 5.39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info