781945
21
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
16 english
For specifi c instructions regarding the drive shaft, refer
to its user manual (delivered with the drive shaft).
For maintenance work or if the splitting wedge is stuck,
disconnect the machine from the tractor rst, after stop-
ping the tractor.
Never leave the machine unattended while it is still con-
nected to the power source!
m Electrical Connection
Inspect the power cords regularly for damage. Make sure
that during this inspection the power cord is not connected
to the mains supply.
The power cords must comply with the applicable VDE
(German Association for Electrical, Electronic, and In-
formation Technologies) and DIN (German Institute for
Standardization) regulations. Use only power cords with
the designation H 07 RN.
A type label on the power cord is prescribed.
Faulty power cords
Power cords often suffer insulation damages.
Causes are:
Pinching, when power cords are routed through windows
or door cracks.
Bending due to improper attachment or routing of the
power cords.
Cuts due to driving over the power cords.
Insulation damages caused by yanking it out of the pow-
er outlet.
Cracks in the insulation because of ageing.
Such faulty power cords must not be used and are, due to
the damaged insulation,
a
danger to life
!
Three-phase motor 400 V/ 50 Hz
Power supply 400 volts / 50 Hz.
Power cord and extension cord must have 5 conductors
= 3 P + N + PR. - (3/N/PE).
The extension wires must have a cross-section of at least
2.5 mm² and must not be longer than 20 m.
The power supply must be protected by a 16 A (or less)
circuit breaker.
After connecting the power supply or after relocating, check
the direction of rotation. Invert polarity if necessary.
Turn the polarity inverter inside the power plug.
Maintenance
Retooling, adjustment and cleaning activities are only to
be carried out when the motor is switched off.
Unplug the mains plug.
Experienced craftsmen may perform minor repairs them-
selves.
Repair and maintenance activities on the electric equipment
may only be carried out by an electronics specialist.
All protection and safety appliances must be tted imme-
diately after completion of repair and maintenance work.
We recommend:
•Clean the machine thoroughly after each use!
Splitting knife
The splitting knife is a consumable which
might need regrinding/re-sharpening or which has to be
replaced with a new one.
Two-hand operating facility
The control and operating facility must remain smooth-
running. Lubricate occasionally with a few drops of oil.
Movable parts
Keep the splitting knife guides clean. (dirt, splinters,
bark, etc.)
Lubricate slide bars with spray oil or grease
Check oil level of hydraulics
Check hydraulic connections and screws for tightness and
abrasive wear. If necessary retighten the screw connec-
tions.
When do I change the oil?
First oil change after 50 operating hours, then always after
250 operating hours.
Check the oil level.
Check the oil level frequently before each start-up. If the
oil level is too low, the oil pump may be damaged.
Note:
The oil level must be checked while the splitting kni-
fe is retracted. The oil dipstick is located on the splitting
column in the ller plug A (Fig. 5) und is provided with 1
slot. If the oil level is at the lower end of the dipstick, this
indicates that the minimum oil level has been reached. If
this is the case, the oil must be refi lled immediately. The
slot indicates the maximum oil level.
The oil tank is situated in the splitting column and is lled
with high-quality hydraulic oil by the manufacturer.
Change of the hydraulic oil and the oil fi lter.
Place a container under the suction hose. Remove the hose
clamp of the pump and pull off the suction hose. Caution:
allow the oil to fl ow into the container! Fig. 7
Remove the suction hose completely and by slightly tilting,
allow the remaining oil to drain into the container.
To change or clean the fi lter, remove the entire intake ma-
nifold by means of a at spanner SW41 or pipe wrench!
Fig. 7.1
Clean the lter and re-mount with new sealing tape, item
no.: 1607 0333. Connect the suction hose again and se-
cure with hose clamps.
Remove the fi ller plug and fi ll with new hydraulic oil.
Attention! Make sure that no dirt particles enter the oil tank.
Dispose of used oil accordingly by taking it to the local waste
oil collection points. It is prohibited to drain used oil into the
soil or to mix it with waste.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach OX7-1600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach OX7-1600 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 11.61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info