782095
31
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
31
• The product meets the requirements of EN 61000-3-11 and is subject to special connection conditions. This means
that use of the product at any freely selectable connection point is not allowed.
• Given unfavorable conditions in the power supply the product can cause the voltage to uctuate temporarily.
• The product is intended solely for use at connection points that
a) do not exceed a maximum permitted supply impedance “Z”, or
b) have a continuous current-carrying capacity of the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consultation with your electric power company if necessary, that the con-
nection point at which you wish to operate the product meets one of the two requirements, a) or b), named above.
Finding the causes of any troubles turned up and their remedy always demands extra attention and caution. Before starting
trouble-shooting, always pull the power supply plug.
In the following, some of the most frequent defects and their causes are listed. In case of any further defects, please
call your dealer.
Problem Possible Cause Remedy
Machine cannot be switched on. No power supply.
Carbon brush worn.
Check power supply.
Take machine to your service point.
Machine switches automatically off
during idle run. No mains supply. Check fuses.
Due to the integrated low-voltage
protection, the machine does not re-
start automatically. Upon return of the
voltage, the machine must be switched
on again.
Machine stops during planing. Overload protection reacts due to blunt
knives, infeed too fast, or chip removal
too thick.
Before work is continued, replace
knives or let cool down the motor.
Response of the overload protection. Too much chip removal
Too fast feed
Blunt knives
Before continuing work, replace the
knives or wait for the motor to cool
down.
Planed surface not smooth. Infeed too fast.
Blunt knives.
Irregular feed.
Reduce infeed speed.
Replace knives.
Apply constand pressure and reduce
feed.
When thicknessing, chip ejection
obstructed (without dust extractor). Chip removal too important.
Blunt knives.
Wood too humid.
Reduce chip removal.
Replace knives.
When surface planing, chip ejection
obstructed (without dust extractor) Chip removal too important.
Infeed to fast.
Blunt knives.
Wood too humid.
Reduce chip removal.
Replace knives.
With surface planing and thicknessing,
chip ejection obstructed (with dust
extractor).
Suction performance too weak. Use a dust extractor unit having an
air-flow rate at the suction connection
of at least 20 m/s.
Rpm drops during planing. Chip removal too important. Reduce chip removal.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Kity DRA 260 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Kity DRA 260 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 2.01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info