Handleiding Scheppach KP-210 Bamato (pagina 27 van 48) (Duits, Engels, Frans)

782508

Verklein

Vergroot

Pagina terug

1/48

Pagina verder

AMAT

Bavarian Machine Tools

Now push the machine head (4) slowly and steadily

to the very back until the saw blade (6) has com-

pletely cut through the work piece.

• When the cutting operation is completed, move

the machine head (4) back to its upper (home)

position and release the ON/OFF button (2).

Attention! The machine executes an upward

stroke automatically due to the return spring, i.e.

do not release the handle (1) after completing the

cut; instead allow the machine head to move up-

wards slowly whilst applying light counter pressure.

8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)

The crosscut saw can be used to make crosscuts of

0° -45° to the left and 0° -45° to the right in relation

to the stop rail.

Important. To make 90° crosscuts, the adjustable

stop rail (16a) must be xed at the inner position.

• Open the set screw (16b) for the adjustable stop

rail and push the adjustable stop rail inwards.

• The adjustable stop rail (29) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Loosen set screw (26).

• Use the handle (11) to adjust the rotary table (14)

to the desired angle. The pointer (12) on the rotary

table must match the desired angle on the scale

(13) on the xed saw table (15).

• Re-tighten the set screw (26) in order to secure the

rotary table (14).

• Cut as described under section 8.3.

8.5 Precision adjustment of the stop for mitre cut

45° (Fig. 1/10/11)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1)

to angle the machine head (4) 45° to the left.

• 45° - position angle stop (b) between the saw blade

(6) and rotary table (14).

• Adjust the adjusting screw (28) until the angle be-

tween the saw blade (6) and rotary table (14) is

precisely 45°.

• It is not necessary to x this setting because it is

maintained by the spring pretension.

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 45° on the angle

scale (18) and re-tighten the retaining screw.

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 1/6/7)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade

(6) and the rotary table (14).

• Adjust the adjusting screw (27) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

• It is not necessary to x this setting because

it is maintained by the spring pretension.

Subsequently check the position of the angle in-

dicator. If necessary loosen the pointer (19) using

a Philips screwdriver, set to position 0° on the an-

gle scale (18) and re-tighten the retaining screw.

8.3 Cross cut 90° and turntable 0° (Fig.8)

In the case of cutting widths up to approx. 100 mm it

is possible to x the traction function of the saw with

the set screw (20) in the rear position. In this position

the machine can be operated in cross cutting mode.

If the cutting width is over 100 mm then it is neces-

sary to ensure that the set screw (20) is loose and

the machine head (4) can move.

Attention! For 90° cross cuts, the moveable stop rail

(16a) must be xed in the inner position.

• Open the set screw (16b) on the moveable stop rail

(16a) and push the moveable stop rail (28) inwards.

• The moveable stop rail (16a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (16a) and the saw

blade (6) is no more than 8 mm.

• Before making the cut, check that no collision

could occur between the stop rail (16a) and the

saw blade (6).

• Tighten the set screw (16b) again.

• Move the machine head (4) to its upper position.

• Use the handle (3) to push back the machine head

(4) and x it in this position if required (dependent

on the cutting width).

• Place the piece of wood to be cut at the stop rail

(16) and on the turntable (14).

• Lock the material with the clamping device (7) on

the xed saw table (15) to prevent the material from

moving during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (4).

• Press the ON/OFF switch (2) to start the motor.

• With the drag guide (21) xed in place:

• use the handle (1) to move the machine head (4)

steadily and with light pressure downwards until

the saw blade (6) has completely cut through the

work piece.

• With the drag guide (21) not xed in place:

pull the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by ap-

plying steady and light downward pressure.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scheppach KP-210 Bamato Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info