782508
26
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
26 GB
B
AMATO
Bavarian Machine Tools
Use the tool that is recommended in this manual.
In doing so, your mitre saw provides optimal per-
formance.
Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op-
erations.
7. Before starting the equipment
The equipment must be set up where it can stand
securely. Secure the machine on a workbench or a
stand with 4 screws through the holes in the xed
saw table (15).
All covers and safety devices have to be properly
tted before the equipment is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
Before you press the ON/OFF switch check that
the saw blade is tted correctly. Moving parts must
run smoothly.
Before you connect the equipment to the power
supply make sure the data on the rating plate are
dentical to the mains data.
Do not use the tool if the switch does not allow
you to switch from the ON state to the OFF state.
8. Attachment and operation
8.1 Attaching the saw (Fig1/2/3/4/5)
In order to adjust the rotary table (14) loosen the
set screw (26) approx. 2 turns.
Turn the rotary table (14) and pointer (12) to the
desired angle measurement on the scale (13) and
secure with the set screw (26).
Pressing the machine head (4) lightly downwards
and removing the locking bolt (23) from the motor
bracket at the same time disengages the saw from
the lowest position.
Swing the machine head (4) up until the release
lever (3) latches into place.
It is possible to secure the clamping device (7) to
the left or right on the stationary saw bench (15).
Insert the clamping device (7) in the hole on the rear
side of the stop rail (16) and secure it with the star
grip screw (7a).
Attach the workpiece supports (8) to the xed saw
table (15) as shown in Figure 5 and fasten with the
screw (9).
It is possible to tilt the machine head (4) a max. 45°
to the left by loosening the set screw (22).
Noise
Total noise values determined in accordance with
EN 61029.
sound pressure level LpA 99.6 dB(A)
uncertainty KpA 3 dB
sound power level LWA 112.6 dB(A)
uncertainty KWA 3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Vibration emission value ah2.5 m/s²
uncertainty K 1.5 m/s²
The specied vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specied value in excep-
tional circumstances;
The specied vibration value can be used to compare
the equipment with other electric power tools.
The specied vibration value can be used for initial
assessment of a harmful effect.
Reduce noise generation and vibration to a mini-
mum!
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adopt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks
can arise during operation.
Health hazard due to electrical power, with the use
of improper electrical connection cables.
Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
Residual risks can be minimised if the „safety in-
structions“ and the „Proper use“ are observed
along with the whole of the operating instructions.
Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
When cutting plastic material, please always use
clamps: the parts which should be cut must always
be xed between the clamps.
Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach KP-210 Bamato bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach KP-210 Bamato in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 5.4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info