782187
11
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
12 english
the bench and guide the saw blade pins into the recess.
Repeatthisprocedurefortheupperbladeholder.Push
the upper arm of the saw slightly downwards before
tighteningthescrews(Fig.9,10,13).
2Checkthepositions ofthe bladepins in both holders
(Fig.12).
3Tensionthebladeusingthetensioningtap.Checkthe
bladetension.Carryonturningclockwisetotensionthe
bladefurther(Fig.11).
Note: It is difficult to open the tensioning tap again if the blade
is too tightly tensioned.
Basic operation
Ascrollsawisfundamentallya„curvecuttingtool“but
which can also carry out straight and angled edge cuts. Fa-
miliarise yourself with the following important points prior
to commissioning the saw.
• Thesawdoesnotautomaticallycutwood.Youmustfeed
the wood against the saw blade manually.
• ThecuttingprocessoccursonIywhilethebladeismov-
ing downwards.
• Feedthewoodslowlyagainstthesawbladeasthesaw
blade teeth are small and cut only while moving down-
wards.
• AlIpersonscarryingoutworkwiththesawrequiretrain-
ing. The saw blade may break easily during this train-
ing time Iwhile the operator is sti1l unfamiliar with the
saw.
• Thesawisbestsuitedtorsheetsofwoodlessthan2.5
cm thick.
• Feedthewoodespeciallyslowlyagainstthebladeand
avoid abrupt curves to prevent the saw blade from break-
ing, if you wish to cut wood sheets thickerthan 2.5 cm.
• Sawbladeteethbluntenovertime,sawbladesmustbe
replaced.Thesawbladesaresufcienttor1/2to2op-
erating time depending upon the type of wood.
• Tryandmakesurethatthesawbladefollowsthegrainof
the wood in order to obtain a clean cut.
• deco 402/decotronic: The saw speed must be reduced
to minimum when cutting precious and non-terrous met-
als.
Inside cuts
Warning: Switch off the saw and remove the mains supply plug
before installing saw blades in order to avoid injuries caused
by unintentional activation of the saw.
This saw is suited also to inside cuts cuts not starting at
the edge of the work piece. Proceed as follows:
• Drilla6mmholeintheworkpiece.
• Loosenthebladetensionerandreleasethetensionin
the blade.
• Placetheboreholeoverthesawbladeslotinthework
bench.
• Installthesawbladethroughtheholeintheworkpiece
and through the work blade slot, and fasten the blade to
the holders.
• Whenyouhavecompletedtheinsidecut,removethesaw
blade and then remove the workpiece from the bench.
m Electrical connection
The installed electric motor is completely wired ready for
operation.
The customer’s connection to the power supply system,
and any extension cables that may be used, must conform
with local regulations.
Important remark:
The motor is automatically switched off in the event of an
overload. The motor can be switched on again after a cool-
ing down period that can vary.
Defective electrical connection cables
Electrical connection cables often suffer insulation dam-
age.
Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinksresulting fromincorrect attachmentor layingof
the connection cable.
• Cutsresultingfromrunningovertheconnectingcable.
• Insulationdamageresultingfromforcefullypullingout
of the wall socket.
• Cracksthroughagingofinsulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely haz-
ardous.
Checkelectricalconnectioncablesregularlyfordamage.
Make sure the cable is disconnected from the mains when
checking.
Electrical connection cables must comply with the regula-
tions applicable in your country.
Single-phase motor
• Themainsvoltagemustcoincidewiththevoltagespeci-
edonthemotor’sratingplate.
• Extensioncablesuptoalengthof25mmusthavea
cross-section of 1.5 mm2, and beyond 25 m at least 2.5
mm2.
• Theconnectiontothemainsmustbeprotectedwitha
16 A slow-acting fuse.
Onlyaqualiedelectricianispermittedtoconnectthema-
chineandcompleterepairsonitselectricalequipment.
Intheeventofenquiriespleasespecifythefollowingda-
ta:
• Motormanufacturer
• Typeofcurrentofthemotor
• Datarecordedonthemachine’sratingplate
• Datarecordedontheswitch’sratingplate
If a motor has to be returned, it must always be dispatched
with the complete driving unit and switch.
m Maintenance
Warning: In the interests of operational safety, always switch
off the saw and remove the mains plug before carrying out
maintenance work.
General
Reapplicationofthewaxcoatingontheworkbenchmakes
feeding the workpiece to the blade easier.
Motor
The mains cable should be replaced immediately if pulled
out, cut or damaged in any other way.
Donotlubricatethemotorbearingsorinternalparts!
Saw arm bearings
Lubricate the saw arm bearings every 50 hours. Proceed
asfollows(Fig.14).
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Deco-Tronic bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Deco-Tronic in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2.91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info