782187
10
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
english 11
maining hazards which are not yet evident may still be
present.
• Remaininghazardscanbeminimizedbyfollowingthe
instructionsin„SafetyPrecautions“,„ProperUse“and
in the entire operating manual.
• Donotforcethemachineunnecessarily:excessivecutt
ing pressure may lead to rapid deterioration of the blade
anda decreasein performance in terms of nish and
cutting precision.
• Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
Scroll Saw Design Features, Fig. 1
1 Quick release and tension lever: forquicktensioningand
removalot the saw blade with a handle on the lever.
2 Blade guard: protects your hands from injury.
3 Work piece holder
4 Shavings blower: keeps the workpiece area free from
dust.
5 decotronic: electronical speed switch
deco 402: Speed switch
6 On/Off switch
7 Angle scale: you can read the angle position of the table
with this scale.
Installation
Setting the saw bench, Fig. 2
Setting the angle scale
• Releasethestarbuttonandbringthesawbench(2)toa
rightangle(3)inrelationtothesawblade.
• Use a 90° angle tc measure the right angle between
thebladeandthebench.Thesawbladebe90°tothe
angle.
• Closethestarbuttonagainwhenthedistancebetween
thebladeandthe90°angleisataminimum.Thebench
shouldthenbeat90°tothesawblade.
• Releasethe lockscrew andbringthe indicatorto the
zero position. Fasten the screw. Please note: the angle
scaleisausefulpieceofsupplementaryequipment,but
should not be used for precision work. Use scrap wood
for saw tests, adjust the bench if neces sary.
Note: The bench should not be on the motor block, this can
cause undesireable noise.
Horizontal saw bench and diagonal cuts, Fig. 2+3
• Thesawbenchcanbepositionedintoa450diagonal
position or be left in the horizontal position.
• Youcanreadofftheapproximateslopeanglebyusing
the angle scale located under the work bench. For more
exact adjustment, use scrap wood for some saw tests;
adjust the bench if necessary.
Blade guard assembly, Fig. 4
Install the blade guard to the holder as shown in the dia-
gram. Secure the screws with a nut and washer.
• Liftthesawontotheframeandbaseandpushitonto
the workbench.
• Familiarizeyourselfwiththesawoperatingelementsand
features.
Mounting the saw on a work bench, Fig. 5
• Aworkbenchmadefromsolidwoodisbetierthanone
made of plywood, as interfering vibrations and noise are
more noticeable with plywood.
• Thenecessarytoolsandsmallpartsforassemblingthe
saw on a workbench are not supplied with the saw. How-
ever,useequipmentofatleastthefollowingsize:
1 Saw body
2 Foam rubber base
3 Work bench
4 Flat seal
5 Washer
6 Hexagonal nut
7Locknut
8 Hexagonal bolt
Ouantity Description
4Hexagonalbolts(6mm)1/420xlength
4Flatseal(7mm)9/321.0
4Washers(7mm)9/321.0.
8Hexagonalnuts(6mm)1/420
First of all, drill holes into the seating surface and then
insert the screws.
• Afoamrubberbaseforreductionofnoiseisnotsupplied
with the saw either. However, we expressly recommend
that you use such a base to keep vibration and noise to
a minimum. Ideal size 410 x 320 mm.
Changing the saw blades
Warning: Switch off the saw and remove the mains supply plug
before installing saw b!ades in order to avoid injuries caused
by unintentiona! activation of the saw.
A. Flat saw blades
A.1 Removing the saw blades, Fig. 7
1 First af all, release the tension via the tensianing tap ta
remave the saw blade.
2Undothescrewsetontheupperbladeholder(Fig.8).
3 Undo the lower holder. To do this, use the spanner which
you can feed through the saw blade slot.
4Removethesawbladebypullingitforwards fromthe
holders and by pulling it through the access hole in the
bench(Fig.9).
A.2 lnstalling the saw blade
1Wheninstallingthesawblade,rstofallpullitthrough
the saw blade slot in the work bench.
Note: In order to avoid tearing or lifting of lightweight work-
pieces, the saw blade teeth should always face down towards
the work bench.
2 Guide the saw blade into the lower holder and fasten the
screws(Fig.9).
3 Guide the other end of the blade into upper holder and
fasten the screws. Push the upper arm of the saw slight-
lydownwardsbeforetighteningthescrews(Fig.10).
4 Tension the blade by turning the tensioning tap clock-
wise.Checkthebladetension.Carryonturningclock-
wisetotensionthebladefurther(Fig.11).
Note: It is difficult to open the tensioning tap again if the blade
is too tightly tensioned.
Saw blade with pins
Note: The upper and lower holders should not be tightened
too much when using saw blades which have pins. The gap
between the holding blocks must be slightly wider than the
saw blade. After installation, the blade is held in place by the
tensioning device.
B.1 Removing the saw blade, Fig. 7
1 First of all, release the tension tap.
2 Take the saw blade out from the upper and lower holder.
Push the upper arm of the saw slightly downwards be-
fore tightening the screws.
B.2 Installing the saw blade
1 Guide one end of the saw blade through the borehole in
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Deco-Tronic bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Deco-Tronic in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2.91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info