781698
29
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
29GB
Then assemble the guide bar with the saw chain as
follows:
Place the guide bar with the saw chain on the chain
wheel (16) and guide bolt (17). Ensure that the
adjustment plate (Fig.3/7A) is showing to you.
Place the saw chain round the chain wheel (16).
Cause the chainsaw to the sprocket and check
whether it is correctly.
The adjustment plate (7a) is fastened to the guide
rail (7) with the screw F.
Place the cover (6) on top and tighten gently with
the lock nut (5).
Now the saw chain has to be correctly tensioned.
Tensioning the saw chain
Warning!
Always pull the plug out of the power socket before
doing any work on the chainsaw!
Wear safety gloves!
Make sure the saw chain (4) is inside the guide
groove of the guide bar (7).
Turn the outer Knob (Fig. 3/5A) clockwise until
the saw chain is correctly tensioned, then rotate
the inside knob (5) to block the guide bar in that
position.
While the inside knob is being tightened, the guide
bar must then be pushed upwards.
Check the chain tension again. Do not tension the
chain too tightly.
When cold, it should be possible to lift the chain in
the middle of the guide bar approx. 5 mm. Tighten
the lock nut (5) securely.
When warm, the saw chain will expand and slacken
and there is a danger of it jumping off the rail
altogether. Re-tension if necessary.
If the saw chain is re-tensioned when hot, it must
be loosened again when the sawing work has been
completed.
Otherwise, the contraction which takes place as the
chain cools would result in excessively high tension.
A new saw chain requires a running-in period of
approx .5 minutes. Chain lubrication is very
important at this stage. After running in, check
chain tension and re-tension if necessary.
9. Working instructions
Transporting the chainsaw
Before transporting the chainsaw, always remove
the plug from the power socket and slide the chain
guard over the rail and chain. If several cuts are to
be performed with the chain saw, the saw must be
switched off between cuts.
Securing the extension lead
Only use extension leads suitable for outdoor use. The cross
section of the cable (max. length of extension cord: 75m)
must be at least 2,5 mm². secure the chainsaw ex to the
extension lead by inserting the extension lead into the strain
relief gap of the housing (Fig..M).Extension leads longer
than 30 m will reduce the performance of the chainsaw.
Chain lubrication
To prevent excessive wear, the saw chain and guide
bar must be evenly lubricated during operation.
Lubrication is automatic. Never work without chain
lubrication. If the chain runs dry, the entire cutting
apparatus will quickly become severely damaged.
It is therefore important to check both chain lubrica-
tion and the oil gauge every use (Fig. 4).
Never use the saw when the oil level is below the
“Min.” mark.
Min.: When only approx. 5 mm of oil is visible
at the lower rim of the oil gauge (15), you must
top up with oil.
Max.: Top up with oil until the window is full.
Chain lubricants
The service life of saw chains and guide bars depends
to a large extent on the quality of the lubricant used.
Old oil must not be used! Use only environment-
friendly chain lubricant. Store chain lubricant only in
containers which comply with the regulations.
Guide bar
The guide bar (7) is subjected to especially severe
wear and tear at the nose and the bottom. To avoid
one-sided wear and tear, turn the guide bar over
every time when you sharpen the chain.
Chain wheel
The chain wheel (16) is subjected to especially high
wear and tear. If you notice deep wear marks on
the teeth, the chain wheel must be replaced. A worn
chain wheel curtails the service life of the saw chain.
Have the chain wheel replaced by a specialist dealer
or your Customer Service.
Chain guard
The chain guard must be clipped onto the chain
and sword as soon as the sawing work has been
completed and whenever the chainsaw has to be
transported.
Chain brake
In the event of kick-back, the chain brake (3) will be
actuated via the front nger guard. The front nger
guard is pushed forwards by the back of the hand
and this causes the chain brake to stop the chain
saw, or rather the motor, within 0.15 s (Fig 5, H).
Releasing the chain brake (Fig 5)
To be able to use your chain saw again, you must
release the saw chain again. First switch off the
chainsaw. Then push the front nger guard (3) back
into the vertical position until it locks in place (Fig
5, I). The chain brake is now fully functional again.
Chainsaw protection
Never use the chainsaw in the rain or in damp
conditions.
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach CSE2400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach CSE2400 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 3.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info