781689
22
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
22 | GB
e) The outside diameter and the thickness of the
insertion tool must correspond to the dimen-
sions of the power tool. Incorrectly measured
insertion tools cannot be adequately shielded or
controlled.
f) Threaded mounting of insertion tools must
match the grinder spindle thread. For inser-
tion tools mounted by anges, the arbour
hole of the insertion tool must t the locating
diameter of the ange. Insertion tools, which do
not t exactly on the grinding spindle of the power
tool, rotate unevenly, vibrate violently and may re-
sult in loss of control.
g) Do not use a damaged insertion tool. Before
each use, inspect the insertion tool such as
abrasive wheels for chips and cracks, back-
ing pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power tool
or insertion tool is dropped, inspect for dam-
age or install an undamaged insertion tool.
After inspecting and installing the tool, posi-
tion yourself and bystanders away from the
plane of the rotating insertion tool and run the
power tool at maximum speed for one minute.
Damaged insertion tools usually break during this
test time.
h) Wear personal protective equipment. Depend-
ing on application, use full face protection,
eye protection or safety goggles. As appro-
priate, wear dust mask, hearing protection,
protective gloves and/or workshop apron ca-
pable of stopping small abrasive or workpiece
fragments. The eye protection must be capable
of stopping ying debris generated by various op-
erations. The dust mask or respirator must be ca-
pable of ltrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
i) Keep bystanders a safe distance away from
your work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of the workpiece or of broken insertion
tools may y away and cause injury even beyond
the immediate work area.
j) Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting tool may contact hidden
wiring. Contact with a “live” wire will also make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
k) Position the cord clear of the rotating inser-
tion tool. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled
into the rotating insertion tool.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools clean and sharp. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the power tool in un-
expected situations.
5) Service
a) Have your power tool serviced by a qualied
repair person using only identical replace-
ment parts. This will ensure that the safety of the
power tool is maintained.
Safety warnings common for grinding, sanding,
wire brushing, or abrasive cutting-off operations:
a) This power tool is intended to function as a
grinder or cut-off tool. Read all safety warn-
ings, instructions, illustrations and data pro-
vided with this power tool. If you do not observe
the following instructions, an electric shock, re
and/or serious injuries may occur.
b) Operations such as sanding, wire brushing
polishing or hole cutting are not recommend-
ed to be performed with this power tool. Oper-
ations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not use insertion tools which are not spe-
cically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d) The permitted speed of the insertion tool
must be at least equal to the maximum speed
indicated on the power tool. An insertion tool
which rotates faster than permitted may shatter
and y off.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach CAG115-20ProS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach CAG115-20ProS in de taal/talen: Duits, Engels, Frans, Pools als bijlage per email.

De handleiding is 4.11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info