782165
17
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
17
DGB
Adjusting the reading glass
Fig.“5
The guide tube must project over the sawblade
to such an extent that the scale on the guide
tube is positioned directly under the zero mark
of the magnifying glass.
Release the two belts of the magnifying glass
and set the graduation mark precisely above the
zero mark of the scale.
Retighten the bolts of the magnifying glass.
Setting before initial operation
The electrical current supply is interrupted
by a limit switch when the housing lid is
opened!
Cutting speeds
Fig. „6“
Band saw are quipped with 2 cutting speed.
IMPORTANT!
The cutting speed may only be set while the
machine is at a full stop. Pull the mains plug!
Two levels
460 m/min. for wood and hardwood
775 m/min. for soft wood
V-belt 10 x 1072 mm
Cutting speed - levels I - II
463 m/min. 1 to 3
775 m/min. 2 to 4
The machine is delivered with apre-set
cutting speed of 775 m/min for wood and hard-
wood
Sawband
Selecting the correct sawband is decisive for
cutting performance. Observethe table of the
Operating Instructions.
Narrow sawbands can cut smaller radii than
broad saw bands.
The smallest radius for blade widths
6/10/15/ 25mm
25/40/75/185 mm
Use only sharpened, awless sawbands.
Faulty sawbands increase the risk of acci-
dents and reduce cutting performance.
Changing sawbands
Fig.“8“
The machine is delivered with a new, stan-
dard sawband (15 mm).
The sawband may only be changed when the
mains plug is pulled!
Always wear suitable gloves when handling
sawbands!
The sawband is loosened for removal by
turning the upper handle counterclockwise.
The new sawband is tensioned by turning the
upper handle clockwise.
IMPORTANT when installing a sawband:
• Reset the counterpressure bearings
and guide rollers.
• Check sawband for aws (cracks,
broken teeth) before installation.
• Check the running direction of the
sawband before placing onto the band
wheels.Teeth should point downwards
towards the saw bench.
• The sawband must be placed between
the upper and lower guide rollers.
• Tighten the placed sawband lightly.
• Tum the band wheel clockwise by
hand and carry out the nal tightening
while the band is running evenly.
• Broad sawbands must be tensioned
more rmly than narrow ones.
• Overtensioning of the sawband can
lead to premature breakage.
Sawband path side correction
Fig.“9“
Side correction may only be carried
out with the machine at a tull stop and
with the mains plug pulled!
The sawband must run on the center of the
band wheels. Loosen the knurled nuts (1) on the
underside of the of the handle.
Turn the upper band wheel by hand in the
cutting direction while simultaneously tuming the
handle to the right (+).
The saw band then runs more toward the rear.
When the sawband runs evenly, re-tighten the
knurled nuts on the handle.
Counterpressure bearing
Fig.10“
lnsure that the sawband runs evenly before
setting the counterpressure bearing.
The setting must be carried out while the
machine is at a full stop!
The counterpressure bearings take the feed
pressure of the workpiece.
Set the counterpressure bearings above and
below saw bench so that they contact the saw-
band lightly. Tum the band wheel by hand in the
sawing direction at the same time.
The counterpressure bearings must run with the
sawband during operation.
Reset the counterpressure bearings every time
the sawband is changed!
Guide rollers
Fig.11“
lnsure that the sawband runs evenly before
setting the guide rollers.
The setting must be carried out while the
machine is at a full stop!
The guide rollers take the side pressure of the
workpiece.
Reset the guide rollers above and below saw
bench to the suitable sawband width. They may
reach up to the base of the teeth of the saw-
band.
Set the guide rollers so that they contact the
sawband lightly. Tum the band wheel by hand in
the sawing direction at the same time.
The guide rollers must run with the sawband
during operation.
The sawband must not jam!
Reset guide rollers every time the sawband
is changed!
Cutting height adjustment
Fig.12“
The setting must be carried out while the
machine is at a full stop!
The cutting height is adjustable from 0 - 400 mm
over the beneh.
Height adjustment is carried out continually
using the large hand wheel and remains in any
position due to the automatie clamping function.
For your own safety, always set the sawband
guide as close to the workpiece as possible.
Sawbench
Fig.13“
The saw bench is set at the factory.
The continuous saw bench swing range reaches
trom + 47° to - 15°.
The greatest swing range allows 45° mitered
cuts.
The setting must be carried out while the
machine is at a tull stop!
One can readjust the bench at a 90° angle to the
sawband using the setting screw (1) under the
bench. (Use a square as an aid)!
Table adjustment to + 47°
• Loosen both lock levers (2).
• Tum the handle (3) clockwise.
• Re-tighten the lock handles (2) in the
desired position according to the scale.
Table adjustment to - 1
• Loosen both lock levers (2).
• Tum the handle (3) one quarter revolution
to the right and swing the adjustment
screw (1) on the ball handle to the lett.
• Tum the handle (3) counterclockwise.
• Re-tighten the lock handles (2) in the
desired position according to the scale.
Test the exact angle setting of the table with
a sampie piece before beginning work.
Parallel alignment of the sawband
to the saw bench
Fig. „14“
Exact parallel alignment is especially important
for work with the traverse cutting gauge spe-
cial accessory.
Check parallel alignment with the fence rail and
a low angle.
Place the fence rail on the saw band running
upwards and downwards. Place the low angle
on the fence rail as weil as along the longitudinal
groove.
If there are deviations, loosen the 8 hexagonal
nuts of the table attachment swinging segment
and readjust the saw bench appropriately.
Re-tighten the hexagonal nuts rmly!
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Basa 7.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Basa 7.0 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info