699460
31
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
SATEL VERSA 29
5.15 Installation of 433 MHz wireless detectors
If the 433 MHz wireless system controller (VERSA-MCU) is connected to the control panel,
you can proceed to installation of the 433 MHz wireless detectors after control panel start-up
and controller identification by the control panel. Before installation of the detector, register it
in the controller and check, if transmissions from the detector located at the planned
installation place can reach the controller. To send a transmission, you can e.g. open the
detector tamper switch. If transmissions from the detector planned installation place do not
reach the controller, select another location. Sometimes, it is sufficient to move the detector
by some ten to twenty centimeters. Only after making sure that the controller receives
transmissions from the detector, you can install the detector permanently.
The wireless detectors must be registered to the alarm system. This can be done using the
DLOADX program or LCD keypad.
5.15.1 Adding new 433 MHz wireless detectors
The control panel can support up to 30 wireless detectors.
DLOADX program
You can add 433 MHz wireless detectors in the “VERSA – Structure” window, “Hardware”
tab, after clicking on the VERSA-MCU controller name in the list of devices.
1. Click on the “Read” button to read the data related to wireless detectors from the
controller (these data are not read after clicking on the
button in the main menu).
2. Click on the zone to which a new wireless detector is to be assigned (you can also select
the zone later in the “New wireless dev.” window).
3. Click on the “New device” button. The “New wireless dev.” window will open.
4. Enter the 7-digit serial number of the added detector. The serial number can be found on
the electronics board or on the enclosure.
5. Open the detector tamper contact.
6. The message will confirm that a new detector has been added (unless you have entered
an invalid serial number, of which you will be informed by a message). The new zone
name will be displayed. You can change it.
7. Click on the “OK” button (you can click on the “Quit” button to cancel adding a new
detector or on the “Next” button to proceed to adding a next wireless detector).
8. Click on the “Write” button to write the new wireless detector data to the controller (these
data will not be written after clicking on the button in the main menu).
LCD keypad
You can add the 433 MHz wireless detectors in the service mode by means of the NEW
DEVICE
function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD.
1. NEW DEVICE).
1. Having started the function, enter the 7-digit serial number of the added detector and
press the key. The serial number can be found on the electronics board or on the
enclosure.
2. Open the detector tamper contact.
3. Information on the detector to be added will be displayed (if nothing happens, it can mean
that you have entered an invalid serial number – if this is the case, press to return
to the submenu). Press to confirm your intention to add a detector.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel VERSA 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel VERSA 5 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel VERSA 5

Satel VERSA 5 Snelstart handleiding - Nederlands - 11 pagina's

Satel VERSA 5 Gebruiksaanwijzing - Nederlands - 44 pagina's

Satel VERSA 5 Snelstart handleiding - Nederlands - 2 pagina's

Satel VERSA 5 Aanvulling / aanpassing - Nederlands - 86 pagina's

Satel VERSA 5 Installatiehandleiding - Nederlands - 35 pagina's

Satel VERSA 5 Snelstart handleiding - Nederlands - 2 pagina's

Satel VERSA 5 Snelstart handleiding - Deutsch - 11 pagina's

Satel VERSA 5 Aanvulling / aanpassing - Deutsch - 89 pagina's

Satel VERSA 5 Gebruiksaanwijzing - Deutsch - 44 pagina's

Satel VERSA 5 Installatiehandleiding - Deutsch - 37 pagina's

Satel VERSA 5 Snelstart handleiding - Deutsch - 2 pagina's

Satel VERSA 5 Snelstart handleiding - English - 11 pagina's

Satel VERSA 5 Aanvulling / aanpassing - English - 87 pagina's

Satel VERSA 5 Gebruiksaanwijzing - English - 32 pagina's

Satel VERSA 5 Gebruiksaanwijzing - English - 42 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info