699464
13
Verklein
Vergroot
Pagina terug
1/31
Pagina verder
SATEL PERFECTA 11
accompanying the exit delay countdown). When setting the partition to one of the above-
mentioned armed modes, hold down the armed mode selection key ( , or ) for
about 3 seconds. The exit delay countdown will not run.
6.3.5 Terminating the exit delay countdown
When the exit delay countdown is running, you can terminate it, thus shortening the exit
delay time. Press and hold down , or for about 3 seconds (it is of no
consequence which key you will press).
6.3.6 Service mode and arming
If you try to arm the system when the service mode is active, you will be informed about it by
a message displayed on the keypad. Press if you want to arm the system.
6.3.7 System problems and arming failure
The alarm system can be configured so that the control panel will perform a check during
arming for any problems preventing the system from being armed. The possible problems
that prevent arming are given below:
at least one zone that must not be violated during arming (the P
RIORITY
option has been
enabled for the zone by the installer) is violated in the partition,
at least one alarm zone is violated beyond the exit route in the partition,
a zone is bypassed in the partition,
there is tamper in the partition,
there is trouble in the system.
The check can be performed twice:
before starting the arming procedure,
after the exit delay countdown expires.
System not ready and forced arming
If you are trying to arm a partition, but the arming procedure fails to start and the “System not
ready” message is displayed instead, there are some problems in the system that prevent it
from being armed.
When the “System not ready 1=Arm 2=Check” message is displayed, you can:
press to cancel the arming,
press to force the arming,
press to check what has prevented the arming procedure from starting.
When the “System not ready 2= Check” message is displayed, you can:
press to cancel the arming,
press to check what has prevented the arming procedure from starting.
If forced arming is not available, you will be able to arm the system only after the
causes that made starting of the arming procedure impossible are eliminated.
List of problems
If, after pressing , it turns out there are several causes that prevent arming, you can
scroll the list using the
or keys.
If you want to bypass a violated zone or unbypass a bypassed zone, press
(you need
to have the Z
ONE INHIBITION
right). A prompt will appear asking you whether to execute the
function. Press to confirm or to deny.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel PERFECTA 16 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel PERFECTA 16 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel PERFECTA 16

Satel PERFECTA 16 Snelstart handleiding - Nederlands - 11 pagina's

Satel PERFECTA 16 Gebruiksaanwijzing - Nederlands - 32 pagina's

Satel PERFECTA 16 Aanvulling / aanpassing - Nederlands - 52 pagina's

Satel PERFECTA 16 Aanvulling / aanpassing - Nederlands - 50 pagina's

Satel PERFECTA 16 Installatiehandleiding - Nederlands - 28 pagina's

Satel PERFECTA 16 Gebruiksaanwijzing - Deutsch - 32 pagina's

Satel PERFECTA 16 Aanvulling / aanpassing - Deutsch - 52 pagina's

Satel PERFECTA 16 Aanvulling / aanpassing - Deutsch - 50 pagina's

Satel PERFECTA 16 Installatiehandleiding - Deutsch - 28 pagina's

Satel PERFECTA 16 Snelstart handleiding - English - 10 pagina's

Satel PERFECTA 16 Aanvulling / aanpassing - English - 49 pagina's

Satel PERFECTA 16 Aanvulling / aanpassing - English - 50 pagina's

Satel PERFECTA 16 Installatiehandleiding - English - 27 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info