699578
32
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
30 Programming CA-6
The keypad with incorrect address is not supported by the control panel. The
address is not controlled, when the panel is in the service mode.
The keypad address is set by the control panel automatically when the default settings are
being programmed (the panel reads out setting of the jumpers and stores it in memory).
The FS111 function enables to check the keypad address and program it. It is necessary
that the same address would be also set by means of the jumpers. It means that the
address set on the keypad pins and the one programmed with this function must be
identical.
The programming in FS111 function consists in lighting up the LEDs 1 to 4, which
correspond to the jumper settings. The settings need to be confirmed with the [#] key.
The [
*
] key enables to quit the function.
Fig. 3. Setting of the jumpers and corresponding LEDs during programming procedure in
the CA-6 KLED keypad.
Notes:
The control panel does not support keypad in which either all jumpers or no jumpers
are set.
When programming the keypad address be particularly careful, as having
programmed a wrong address may trigger a tamper alarm at the moment you exit
the service mode and cause a loss of control from the keypad. Then it is necessary
to enter the service mode by hardware means and read the new address (see:
Installer Manual).
The new address (as most of the programmed parameters of the panel) will become
valid after exiting the service mode or when the panel is being programmed from the
computer - after the data are sent.
Automatic readout of the keypad address without changing the other control panel
parameters is possible by means of the FS124 function.
FS112 - start of programming from computer in local mode
The function starts the programming mode through a modem or RS-232 TTL port. The
function is called upon a prompt from the computer. Prior to using the function, hook up
the control panel to the computer (see: Installer Manual). Start the DLOAD10 program on
the computer. After calling the function, the panel will first try to establish connection
through the RS port, and if fails, via the telephone line.
address
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's

Satel CA-6 Installatiehandleiding - English - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info