699578
31
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
CA-6 SATEL 29
3 - controls output OUT3
4 - controls output OUT4
5 - controls output OUT5
6 - not used – do not program
7 - partition control timer (guard rounds)
8 - controls A partition
9 - controls B partition
Note: Do not program the values 6 and A to F. The partition control function (7) can
only be programmed for timer 1 (A partition control) and timer 2 (B partition
control).
The Guard rounds control requires the following parameters:
guard code in the controlled partition (a code with authority level 5 it also performs
the function of activating the MONO SWITCH).
partition control timer – the hour and minute set for switching on this timer defines
the maximum time that may elapse since the last time the guard code was entered - if
it is exceeded, the “no control code” event is recorded in the memory, the information
is sent to the monitoring station, and the “no guard round” type output is activated.
Entering the code by the guard is recorded in the event memory as the “entry/exit”
event.
EXAMPLE:
programming the function: TIMER1 - controls A partition, TIMER 2 - controls OUT4
output, TIMER 3 and TIMER 4 - control OUT5 output.
[12345] [#] - enter the service mode
[1][0][6] [#] - call the function
[8][4] [#] - program the timers 1 and 2 functions (B diode is blinking)
[5][5] [#] - program the timers 3 and 4 functions (A diode is blinking) and exit the function
Special functions
FS107 - restoring default settings
Calling this function will restore all the factory default settings of the control panel
parameters (see: „Default settings” section, Installer Instruction) and will automatically read
the current address of the keypads. The service code is set as [1][2][3][4][5]. The function
does not change the user access codes.
FS108 - clearing event log
Calling this function will erase the memory of events.
FS109 - restoring default communication passwords
Calling this function will restore the factory default control panel and computer identifiers
(see: FS2, FS3), which are required to establish communication with the computer. These
settings are used for testing the control panel.
FS110 - restoring default codes
Calling this function will erase all the user access codes and restore the default MASTER
code [1][2][3][4] and the default service code [1][2][3][4][5].
FS111 - programming keypad address (BIT)
The keypad of CA-6 control panel has its individual address, which is set with jumpers.
The panel imports this address together with other keypad data (zone state, depressed
keys, tamper contact state) and compares with the address programmed in the nonvolatile
memory. If a difference is detected, a tamper alarm is triggered.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's

Satel CA-6 Installatiehandleiding - English - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info