699578
19
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
CA-6 SATEL 17
ON
operation time in minutes
6
OFF
operation time in seconds
ON
LATCH type output – signaling until cleared (operation time irrelevant)
7
OFF
programmable output operation time
ON
polarity +12V when the output is active
8
OFF
polarity 0V when the output is active
Note: The option of output assignment to the partition is to be used, when separate
sirens have to be assigned to individual partitions. If not assigned to a partition,
the alarm output will signal every alarm.
EXAMPLE:
programming the OUT1 output as the BURGLARY/FIRE ALARM type with 5 minutes
operation time and polarity 0V in active state
[12345] [#] - enter the service mode
[3][1] [#] - call the function. The LEDs 1-8 shows number of current output type (LEDs 1-4 shows
binary first digit, LEDs 5-8 – second digit). The blinking B LED signals the output type
being programmed
[0][2] [#] - enter and confirm the number of output function (the A LED starts blinking - operation
time programming)
[0][5] [#] - program and confirm the time (A and B LEDs start blinking - output option programming)
[6] - LED 6 goes on - the „time in minutes” option is activated
[8] [#] - LED 8 goes off - set the "polarity" = 0V and exit the function
Note: Choosing a partition in the options will determine which access code is to be
used to switch off siren or to control a zone. The same effect is provided by
defining a list of zones controlling the outputs.
FS32 - programming list of zones for OUT1 (BIT)
The function is used to program the output controlling zones. The selection of zones limits
the output operation only to the reaction to violation of those particular zones.
The zone selection should only be used when it is necessary to have separate
signaling for events from a specific zone or a group of zones. If no list of zones is
programmed, the control panel will assume by default that the output reacts to events from
any zone – for example, the BURGLARY alarm type output will signal alarms for each
control panel alarm zone. Of course, the zone function (reaction type) is taken into
consideration, e.g. the alarm signaling output does not react if the state of the arming zone
changes.
If the list of zones has been programmed the control panel will skip the programmed
selection of partitions.
The FS32 function is used to assign zones to the OUT1 output. The programming consists
in lighting up the LEDs which correspond to the zones. When the list is completed, it
should be confirmed.
FS33 - programming OUT2 output
The function allows for defining the basic parameters associated with the OUT2 output.
The programming procedure is the same as for the FS31.
FS34 - programming list of zones for OUT2 (BIT)
The function programs the list of zones associated with the OUT2 output. The
programming procedure is the same as for the FS32.
FS35 - programming OUT3 output
The function defines the basic parameters associated with the OUT3 output. The
programming procedure is the same as for the FS31.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's

Satel CA-6 Installatiehandleiding - English - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info