699578
12
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
10 Programming CA-6
EXAMPLE:
programming the counters: the 1
st
- 2 violations, the 2
nd
- 5 violations, the 3
rd
- without
changes
[12345] [#] - enter the service mode
[7] [#] - call the required function
[0][2] [#] - program the first counter (the lower B LED is blinking)
[0][5] [#] - program the second counter (the lower LED A is blinking)
[
*
] - exit the function - programming of the third counter is omitted
In case of programming three counters, the function is automatically exited after the third
counter
Functions programming assignment
FS8 - programming A partition zones (BIT)
FS9 - programming B partition zones (BIT)
The functions FS8 and FS9 are used to divide the alarm system into partitions.
It is possible to assign any zone to the partitions. Independent sirens and messaging
telephone numbers can be assigned to the partitions, and separate access codes can be
programmed – thus creating two independent alarm systems.
Optionally, the so-called interior partition can also be created (if one partition is to be fully
contained in the other).
When both partitions are armed, it is possible to disarm the interior partition by
using its code. The other zones, which belong to the primary partition, will remain
armed.
Note: If the armed mode is activated by means of the primary partition code, the interior
partition zones will be automatically armed as well, but their status as a partition
status will not be signaled by the control panel – the
[
ARMED
] LED, which
corresponds to the interior partition, is "off".
A zone can be assigned to both partitions at the same time. The common zone will only be
armed, when both partitions are armed (if the partitions do not contain one another, i.e. the
partition is not the interior one).
Zones can be assigned to the partition by pressing the keys 1 to 8, which is shown by
lighting of the LED which indicates the respective zone. Use the [#] key to confirm the
selection and exit the function. Use the [
*
] key to interrupt the programming.
FS16 - programming auto bypassed zones in A partition (BIT)
The AUTO BYPASS function applies to the zones which are automatically bypassed after
arming with the 7 authority level code (partial arming), assigned to the A partition. The
same zones are bypassed after silent arming of the A partition.
The control panel permits also programming another set of automatically bypassed zones:
bypassed when no exit from the partition (EXIT-BYPASS zones - with service functions
FS127, FS128).
The programming is similar to the programming of FS8 function. After the corresponding
diodes are turned on the [#] key should be pressed.
FS17 - programming bypassed zones in B partition (BIT)
The function refers to the automatically bypassed zones in B partition. The programming
as in FS16.
FS20 - programming keypad and partition options (BIT)
Some of the user functions and the keypad beeps are optional. The FS20 function defines
which of them are to be performed.
Two sets of options are programmed, each of them need to be confirmed with the [#] key.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's

Satel CA-6 Installatiehandleiding - English - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info