797034
14
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
13
GB
F
E
NL
D
There are 3 different bandwidth settings available for the
AIR and FM bands, while the SW, MW and LW bands
each have 5 different bandwidth settings:
Bandwidth Indicator FM MW /
LW SW AIR
WIDEST 110kHz 6kHz 4kHz 6kHz
WIDE - 4kHz 3kHz -
NORM 85kHz 3kHz 2.5kHz 4kHz
NARROW - 2.5kHz 1.8kHz -
NARROWEST 65kHz 1.8kHz 1kHz 2kHz
To use automatic bandwidth control, place the Bandwidth
Control switch (13) in the AUTO position. The bandwidth
will now automatically be adjusted to the best setting
according to the signal to noise ratio and the radio will
keep monitoring the signal to noise ratio every 300 ms
and adjust the bandwidth if needed.
It is also possible to manually adjust the bandwidth. To do
this, follow these steps:
1. Turn on the radio using the Power button (10).
2. Select the desired waveband by pressing the
corresponding button.
3. Place the Bandwidth Control switch (13) in the manual
position.
4. Press the bandwidth button (26) repeatedly to select
the desired bandwidth.
The Bandwidth indicator (Ad) on the display shows the
currently selected bandwidth.
NOTE
The bandwidth cannot be set when using the LSB or
USB band. Pressing the Bandwidth Control button (26)
has no effect in this case.
PERFORMING A PAGE SCAN – AIR
ONLY
When using the AIR band, the AIR button (23) can be
used to perform a page scan. When performing a page
scan, the ATS-909X2 will tune to all preset stations that
are saved on the current page and stop when it finds a
station on which a signal is being received. If the signal
is no longer received for the duration of the scan delay,
the radio will continue scanning the other presets on the
current page (see chapter 6 "USING THE MENU" for
more information about setting the page scan delay).
To perform a page scan, follow these steps:
1. Turn on the radio using the Power button (10).
2. Select the AIR band using the AIR button (23).
3. Select the desired page using the Page button (27).
4. Press and hold the AIR button (23).
5. The radio will now perform a page scan, scanning all
presets on the current page until it finds a preset that is
broadcasting a signal.
6. If no suitable station can be found the radio will keep
scanning the selected page.
7. To cancel the page scan, press the AIR button (23)
once again.
NOTE
The common airband is normally used for short-term
transmission. The page scan feature can monitor 9
preset stations at the same time. If a radio signal is
being received on a certain preset, the radio will stop
scanning and tune to that preset. When the radio no
longer receives a signal on this frequency, it will wait
0.5 second to 2 seconds (depending on the set scan
delay) and, if no signal is being received anymore, then
continue the page scan.
SETTING THE SQUELCH LEVEL
Background hiss or static noise is present to some
degree at every location. This is a normal phenomenon.
The Squelch button (8) can be used to set the squelch
level above the background noise level in order to skip
unwanted stations or interference when automatically
scanning, making it easier to find voice transmissions
from stronger stations.
It is recommended to keep the squelch level as low
as possible (to a level just before static noise can be
constantly heard). This way, signals that may be weak
can still be heard. If the squelch level is set too high, weak
voice transmissions may be suppressed as well.
The squelch level can be adjusted using the following
steps:
1. Turn on the radio using the Power button (10).
2. Press the Squelch button (8).
The Squelch indicator (N) will now be shown on the
display and 'SQUELCH' is blinking in the Text display
(U).
3. Rotate the Tuning Control knob (16) clockwise to
increase the squelch level or counterclockwise to
decrease the squelch level.
When the receiving RF level is lower than the set
squelch level, the Squelch indicator (N) will be shown
on the display of the radio.
SETTING THE RF GAIN
The AM RF Gain jog dial (40) can be used to enhance the
gain of the RF amplifier while listening to the AM band.
A higher gain level helps receiving signals from further
away, but can also saturate the RF amplifier when the
radio is situated near a strong electric field, causing it to
no longer receive any normal signal. In this case, the RF
gain should be lowered to avoid such saturation effects.
In general, it is recommended to place the AM RF
Gain jog dial (40) in the maximum position for the best
reception.
6. USING THE MENU
The menu of the ATS-909X2 can be accessed by
pressing and holding the Menu button (29) while the
radio is powered on or off. After accessing the menu, the
Rotary Tuning knob (16) can be used to browse through
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sangean ATS-909X2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sangean ATS-909X2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Sangean ATS-909X2

Sangean ATS-909X2 Gebruiksaanwijzing - Nederlands - 21 pagina's

Sangean ATS-909X2 Gebruiksaanwijzing - Deutsch - 20 pagina's

Sangean ATS-909X2 Gebruiksaanwijzing - Français - 21 pagina's

Sangean ATS-909X2 Gebruiksaanwijzing - Espanõl - 21 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info