167811
23
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
4. CROSSOVER SETTINGS
23
4.1 MINIMUM IMPEDANCE LOAD
The output stages of the RODEK R680A2 multichannel amplifier
are designed to give you extraordinary output power into 4 or 2
Ohms loads in normal stereo configurations. In bridged mode,
the minimum impedance load is 4 ohms. We put emphasis on
the fact, that the amplifier might suffer from thermal shut-down
or even damage, if these recommended minimum impedance
load ratings are not considered appropriately.
4.2 SELECTING THE OPERATION
MODE
The R680A2 is multi-channel concept amplifier with integra-
ted active crossovers and thus, offers different amplification
modes which can be set by the operation mode slide switches.
Three of these switches can be found on the R680A2 amp.
These switches enable you to configure each stereo channel
pair to work in either in fullrange, highpass or even bandpass
mode. Therefore - before you get started with the settings of
crossover frequencies and input gain adjustments - you must
select the appropriate operation mode for each channel pair of
your RODEK amplifier, depending on the speaker system that
is connected and driven by the amp. This will make sure that
every speaker system is only working in its proper frequency
operation range, for which the speaker was designed. For
example select HIGHPASS, if the speaker is a component- or
coaxial type, or BANDPASS in case of a kickbass or subwoofer
system - and finally FULL(range) if the passband frequency of
the stereo channel is already controlled by a head-unit with
an integrated DSP based active crossover.
4.2.1 HIGHPASS FOR COMPONENT
AND COAXIAL SPEAKERS
Before you start your adjustments, all tone controls (i.e. Bass,
Treble), fader/balance and loudness featured on the head unit,
must be set to their respective neutral or center position.
Please take a look at the chart below, featuring the sugges-
ted high-pass cross-over frequency settings for coaxial- and
component speaker systems - and adjust the highpass control
of each channel pair that drives satellites speaker systems
accordingly. The most important factor for the individual adjus-
tment of the highpass crossover frequency is the reproduction
of mid-bass frequencies and the resulting power-handling of
the speaker system. This setting is always a compromise. Try
to find a highpass crossover point, that will suit your personal
listening preferences and - at the same time - also considers the
physical (cone excursion) capabilities of your speakers best.
Satellite speaker system, front door mounted, recommended
highpass frequency
10 cm Coaxial- or Component System 90 - 120 Hz
13 cm Coaxial- or Component System 80 - 100 Hz
16 cm Coaxial- or Component System 60 - 90 Hz
Satellite speaker system, rear mounted, recommended
highpass frequency
10 cm Coaxial- or Component System 100 - 150 Hz
13 cm Coaxial- or Component System 120 - 150 Hz
16 cm Coaxial- or Component System 130 - 150 Hz
R680A2 Manual_E+D.indd 23R680A2 Manual_E+D.indd 23 07.07.2004 12:36:46 Uhr07.07.2004 12:36:46 Uhr
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 680 a 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 680 a 2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info