167811
21
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
2. MOUNTING OF THE AMPLIFIER
21
Before you attempt the installation of your R680A2 6-channel
amplifier, it is recommended to map out the complete audio
system and the respective wiring required. Please note that
- because of possible interference problems with the existing
car electrics and electronics - especially the routing of the
signal cables and the chassis ground connection will have a
profound impact on the performance of the overall system.
Secondly, the correct mounting location needs your attention
too (proper cooling of the amp!). Use only quality installation
material and if you have only little or no experience with complex
car audio installations, we strongly recommend you to consult
your nearest authorized RODEK dealer/installer.
2.1 MOUNTING LOCATION
The mounting location should be carefully selected, prefe-
rably in the trunk compartment of your car! In the interest of
passive driver and passenger safety, the amplifier must be
securely mounted, and special precautions must be taken
to allow sufficient cooling. The amp can get quite hot during
operation, so a clearance of at least 5cm from both sides and
from the top of the amp must be considered.
Furthermore, this amplifier features an internal fan, so the
side panels must not be covered to allow for a good air flow
in and out of the side-panel windows.
Make sure there is no wiring harness, fuel tank etc. behind
or below the mounting surface that may be damaged by the
drilling of the holes for the amplifier mounting screws. The
above mentioned clearance of at least 5cm to all sides of the
amplifier is not only for proper cooling, but also because the
crossover controls must remain accessible. The amplifier must
NOT be mounted directly to the chassis ground of the vehicle,
this may cause to ground loops with loud hum noise.
3. ELECTRICAL WIRING
IMPORTANT! Disconnect the positive battery terminal
(+12V) or remove the main fuse near the car battery
before you start any wiring work!
The power supply of the car audio system must be dis-
connected until the entire wiring installation is com-
pleted.
The recommended minimum power cable cross-section
of the main power supply cable is 20mm², but if you drive
the amp hard a 35mm² power cable is preferrable.
Using main power cables with smaller cross sections
potentially result in unnecessary over-heating of the
amplifier circuitry, distortion at high volume levels
and may also cause the thermal protection circuitry to
shut-off the amplifier.
Use rubber grommets when running cables through any me-
tal or sharp plastic panels, to prevent accidental shorting or
shearing. Make sure the cables do not interfere with normal
operation of the vehicle.
Especially the music signal cables (RCA interconnects) should
be kept far away from any potential sources of electrical inter-
ference e.g. electronic vehicle management systems (engine
computers, relays etc.) fuel pumps, wiring harnesses etc.!
R680A2 Manual_E+D.indd 21R680A2 Manual_E+D.indd 21 07.07.2004 12:36:45 Uhr07.07.2004 12:36:45 Uhr
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 680 a 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 680 a 2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info