512484
80
Verklein
Vergroot
Pagina terug
1/268
Pagina verder
EN
26
Wire position
Press GO to test
Zone setup
Press GO
Main display -
Press ‘GO
Settings
Press GO
Press ‘GO
Mowing
Press GO
Press ‘GO’ and follow
Robomow while following
the Perimeter Wire
Child guard
Press GO
Wire position
Press GO
Scroll down until
Settings’ is displayed
Scroll up until ’Wire
position’ is displayed
Press ‘GO
Wire position
Press GO to test
Wire position
Press GO to test
Zone setup
Press GO
Zone setup
Press GO
Zone setup
Press GO
Main display -
Press ‘GO
Settings
Press GO
Press ‘GO
Mowing
Press GO
Mowing
Press GO
Press ‘GO’ and follow
Robomow while following
the Perimeter Wire
Child guard
Press GO
Wire position
Press GO
Scroll down until
Settings’ is displayed
Scroll up until ’Wire
position’ is displayed
Press ‘GO
Take the Perimeter Switch and squeeze the
tabs on both sides of the Perimeter Switch,
(as shown in figure 1.41) and remove the
back cover from the Perimeter Switch.
Connect the power supply plug to the
Perimeter Switch board (see figure 1.42) and
reassemble the Perimeter Switch.
Connect the power supply to a regular
household receptacle 230 Volts AC;
The Power Supply is for indoor use only, thus
place it in a dry location, which is well
ventilated (do not cover it with plastic bag); be
sure the power supply and the connection to
the low voltage cable are in a dry place and
not exposed to water and rain.
Press the ‘ON’ button. A small flashing green light next to the ‘ON’ button indicates that the
system is on and functioning properly. The Perimeter Switch also has indicators for a
disconnected/broken perimeter wire and for poor wire splicing. Figure 1.43
The Perimeter Switch has an automatic shutoff feature, eliminating the need for you to turn it off
after each use. It will shut itself off after 12 hours of operation. You may manually turn the
perimeter switch off by pressing the ‘
ON’ button continuously for 3 seconds. A beep will be heard
after the three seconds, indicating you may release the button and the switch is off.Test the
perimeter wire setup by choosing the ‘
Wire position’ menu as shown in figure 1.44. Robomow
will follow the wire, while the mowing motor is switched off to prevent any damage to the
perimeter wire after the initial setup; Walk along the side of the Robomow while it is following the
edge until completing one loop of the perimeter without striking any object; If Robomow collides in
obstacle, it stops and drives back to allow you adjusting the wire position.
Figure 1.43
Perimeter Switch
Operating Panel
Flashing light indicates
the system is on
Indicates poor splicing of
perimeter wires or perimeter
wire, which is too long
Indicates a
disconnected/broken wire
ON button
Figure 1.44
Testing the Perimeter
Wire position
Figure
1.41
Figure 1.42
Connect the power supply plug
to the Perimeter Switch board
80

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Robomow-Tuscania-500

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow Tuscania 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow Tuscania 500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 9,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info